 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| INTEGRATED CIRCUITS DEVICE SPECIFICATION DATA SHEET TDA955X/6X/8X PS/N1 series TV signal processor-Teletext decoder with embedded -Controller Tentative Device Specification File under Integrated Circuits, Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller GENERAL DESCRIPTION The various versions of the TDA955X/6X/8X PS/N1 series combine the functions of a video processor together with a -Controller and US Closed Caption decoder. Several versions have a Teletext decoder on board. The Teletext decoder has an internal RAM memory for 1or 10 page text. The ICs are intended to be used in economy television receivers with 90 and 110 picture tubes. The ICs have supply voltages of 8 V and 3.3 V and they are mounted in an S-DIP 64 envelope. The features are given in the following feature list. The differences between the various ICs are given in the table on page 4. FEATURES TV-signal processor * Multi-standard vision IF circuit with alignment-free PLL demodulator * Internal (switchable) time-constant for the IF-AGC circuit * A choice can be made between versions with mono intercarrier sound FM demodulator and versions with QSS IF amplifier. In the QSS versions without East-West output an AM/FM mode can be activated. In that case both the QSS amplifier (for AM demodulation) and the FM demodulator are available. * The mono intercarrier sound circuit has a selective FM-PLL demodulator which can be switched to the different FM sound frequencies (4.5/5.5/6.0/6.5 MHz). The quality of this system is such that the external band-pass filters can be omitted. * The FM-PLL demodulator can be set to centre frequencies of 4.74/5.74 MHz so that a second sound channel can be demodulated. In such an application it is necessary that an external bandpass filter is inserted. * The QSS amplifier and mono intercarrier sound circuit of some versions can be used for the demodulation of FM radio signals * Source selection between the `internal' CVBS and one external CVBS or Y/C signal * Integrated chrominance trap circuit * Integrated luminance delay line with adjustable delay time * Picture improvement features with peaking (with switchable centre frequency, depeaking, variable positive/negative overshoot ratio and video dependent coring) and blue- and black stretching TDA955X/6X/8X PS/N1 series * Integrated chroma band-pass filter with switchable centre frequency * Only one reference (12 MHz) crystal required for the -Controller, Teletext- and the colour decoder * PAL/NTSC or multi-standard colour decoder with automatic search system * Internal base-band delay line * Indication of the Signal-to-Noise ratio of the incoming CVBS signal * RGB control circuit with `Continuous Cathode Calibration', white point and black level off-set adjustment so that the colour temperature of the dark and the light parts of the screen can be chosen independently. * A linear RGB/YUV/YPBPR input with fast blanking for external RGB/YUV sources. The synchronisation circuit can be connected to the incoming Y signal. The Text/OSD signals are internally supplied from the -Controller/Teletext decoder. * Contrast reduction possibility during mixed-mode of OSD and Text signals * Adjustable `wide blanking' of the RGB outputs * Horizontal synchronization with two control loops and alignment-free horizontal oscillator * Vertical count-down circuit * Vertical driver optimized for DC-coupled vertical output stages * Horizontal and vertical geometry processing * Horizontal and vertical zoom function for 16 : 9 applications * Horizontal parallelogram and bow correction for large screen picture tubes * Low-power start-up of the horizontal drive circuit 2000 Jun 22 2 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller -Controller * 80C51 -controller core standard instruction set and timing * 1 s machine cycle * 32 - 128Kx8-bit late programmed ROM * 3 - 12Kx8-bit Auxiliary RAM (shared with Display and Acquisition) * Interrupt controller for individual enable/disable with two level priority * Two 16-bit Timer/Counter registers * One 16 bit Timer with 8-bit Pre-scaler * WatchDog timer * Auxiliary RAM page pointer * 16-bit Data pointer * Stand-by, Idle and Power Down (PD) mode * 14 bits PWM for Voltage Synthesis Tuning * 8-bit A/D converter * 4 pins which can be programmed as general I/O pin, ADC input or PWM (6-bit) output Data Capture * Text memory for 0, 1 or 10 pages * In the 10 page versions inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) * Data Capture for US Closed Caption * Data Capture for 525/625 line WST, VPS (PDC system A) and Wide Screen Signalling (WSS) bit decoding * Automatic selection between 525 WST/625 WST * Automatic selection between 625 WST/VPS on line 16 of VBI * Real-time capture and decoding for WST Teletext in Hardware, to enable optimized -processor throughput * Automatic detection of FASTEXT transmission * Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters * Signal quality detector for video and WST/VPS data types * Comprehensive teletext language coverage * Full Field and Vertical Blanking Interval (VBI) data capture of WST data Display TDA955X/6X/8X PS/N1 series * Teletext and Enhanced OSD modes * Features of level 1.5 WST and US Close Caption * Serial and Parallel Display Attributes * Single/Double/Quadruple Width and Height for characters * Scrolling of display region * Variable flash rate controlled by software * Enhanced display features including overlining, underlining and italics * Soft colours using CLUT with 4096 colour palette * Globally selectable scan lines per row (9/10/13/16) and character matrix [12x10, 12x13, 12x16 (VxH)] * Fringing (Shadow) selectable from N-S-E-W direction * Fringe colour selectable * Meshing of defined area * Contrast reduction of defined area * Cursor * Special Graphics Characters with two planes, allowing four colours per character * 32 software redefinable On-Screen display characters * 4 WST Character sets (G0/G2) in single device (e.g. Latin, Cyrillic, Greek, Arabic) * G1 Mosaic graphics, Limited G3 Line drawing characters * WST Character sets and Closed Caption Character set in single device 2000 Jun 22 3 FUNCTIONAL DIFFERENCE BETWEEN THE VARIOUS IC VERSIONS 2000 Jun 22 4 Philips Semiconductors TV signal processor-Teletext decoder with embedded -Controller IC VERSION (TDA95XX PS) TV range Mono intercarrier multi-standard sound demodulator (4.5 - 6.5 MHz) with switchable centre frequency Audio switch Automatic Volume Levelling Automatic Volume Levelling or subcarrier output (for comb filter applications) QSS sound IF amplifier with separate input and AGC circuit AM sound demodulator without extra reference circuit AM/FM option FM radio option (via QSS amplifier) FM radio option (with FM tuner) Dynamic Skin tone control PAL decoder SECAM decoder NTSC decoder Horizontal geometry (E-W) Horizontal and Vertical Zoom ROM size User RAM size Teletext Closed captioning 50 51 52 53 54 60 61 62 63 64 65 66 67 80 81 82 83 84 85 86 87 88 90 90 90 110 90 90 90 110 110 110 110 90 90 90 90 90 110 110 110 110 90 110 TDA955X/6X/8X PS/N1 series 32 - 32 - 32 - 32 - 32 - 64- 64- 64 - 64 - 64 - 64 - 64 - 64 - 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 64 k 128k 128k 128k 128k 128k 128k 128k 128k 1k 1k 1k 1k 1k 2k 2k 2k 2k 2k 2k 2k 2k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1 1 1 1 1 10 10 10 10 10 10 10 10 page page page page page page page page page page page page page Tentative Device Specification Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller QUICK REFERENCE DATA SYMBOL Supply VP IP Input voltages ViVIFrms) ViSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(p-p) ViRGB(p-p) ViY(p-p) ViU(p-p) / ViPB(p-p) ViV(p-p) / ViPR(p-p) Vo(IFVO)(p-p) Vo(QSSO)(rms) video IF amplifier sensitivity (RMS value) QSS sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) luminance input signal (peak-to-peak value) U / PB input signal (peak-to-peak value) V / PR input signal (peak-to-peak value) supply voltages supply current PARAMETER TDA955X/6X/8X PS/N1 series MIN. - - - - - - - - - - - TYP. - - - - - - - - - - - MAX. UNIT 8.0/3.3 tbf V mA V V mV V V V V V V 35 60 500 1.0 0.3 0.7 1.4 / 1.0 -1.33 / +0.7 -1.05 / +0.7 Output signals demodulated CVBS output (peak-to-peak value) sound IF intercarrier output in QSS versions (RMS value) - - - - 0 - 10 1 1.2 2.0 100 500 2.0 - 2.0 - - - - - - - 5 - - - - V mV mV V mA V mA mA mA Vo(AMOUT)(rms) demodulated AM sound output in QSS versions (RMS value) Vo(CVBSO)(p-p) selected CVBS output (peak-to-peak value) Io(AGCOUT) VoRGB(p-p) IoHOUT IoVERT IoEWD tuner AGC output current range RGB output signal amplitudes (peak-to-peak value) horizontal output current vertical output current (peak-to-peak value) EW drive output current 2000 Jun 22 5 (AVL) RESET VPE LED OUT (2x) SCL SDA VST OUT AUDEXT AUDOUT Philips Semiconductors TUNERAGC DEEMPHASIS ENHANCED 1/10 PAGE MEMORY 80C51 CPU VST PWM-DAC I/O PORTS AUDIO SWITCH (AVL) VOLUME CONTROL IFIN VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP. I2C-BUS TRANSCEIVER REF H CVBS ROM/RAM ACQUISITION V TELETEXT TELETEXT/OSD DISPLAY VIDEO SWITCH CVBS/Y VIDEO IDENT. C SYNC BASE-BAND DELAY LINE COR VIDEO FILTERS AGC CIRCUIT NARROW BAND PLL DEMODULATOR R G ADC IN (4x) I/O PORTS (4x) 2000 Jun 22 DEEMPHASIS +3.3 V B BL CONTR/BRIGHTN OSD/TEXT INSERT CCC WHITE-P. ADJ. RGB H-DRIVE V-DRIVE + V GEOMETRY (EW GEOMETRY) U V 2nd LOOP H-SHIFT RGB/YUV INSERT Y RGB/YUV MATRIX SATURATION YUV/RGB MATRIX RO GO B0 BCLIN BLKIN BLOCK DIAGRAM SOUND TRAP TV signal processor-Teletext decoder with embedded -Controller 6 LUMA DELAY PEAKING BLACK STRETCH HOUT V-DRIVE EHTO (EWD) REF (REFOUT) PAL/SECAM/NTSC DECODER H/V SYNC SEP. +8V H-OSC. + PLL H R/V G/Y B/U BL TDA955X/6X/8X PS/N1 series Tentative Device Specification Fig. 1 Block diagram TDA955X/6X/8X PS/N1 series with mono intercarrier sound demodulator SIFIN RESET VPE LED OUT (2x) SCL SDA VST OUT QSSO/AMOUT/AUDEXT AUDOUT/AMOUT Philips Semiconductors TUNERAGC QSS SOUND IF AGC QSS MIXER AM DEMODULTOR I/O PORTS 80C51 CPU VST PWM-DAC MEMORY ENHANCED 10 PAGE IFIN VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP. I2C-BUS TRANSCEIVER REF LUMA DELAY PEAKING ROM/RAM ACQUISITION V BLACK STRETCH SYNC BASE-BAND DELAY LINE CVBS TELETEXT H TELETEXT/OSD DISPLAY VIDEO SWITCH CVBS/Y VIDEO IDENT. C COR VIDEO FILTERS ADC IN (4x) I/O PORTS (4x) 2000 Jun 22 +3.3 V R G B BL CONTR/BRIGHTN OSD/TEXT INSERT CCC WHITE-P. ADJ. RGB H-DRIVE V-DRIVE + V GEOMETRY EW GEOMETRY U V 2nd LOOP H-SHIFT RGB/YUV INSERT Y RGB/YUV MATRIX SATURATION YUV/RGB MATRIX RO GO BO BCLIN BLKIN SOUND TRAP TV signal processor-Teletext decoder with embedded -Controller 7 HOUT V-DRIVE EHTO EWD REF (REFOUT) PAL/SECAM/NTSC DECODER H/V SYNC SEP. +8V H-OSC. + PLL H R/V G/Y B/U BL TDA955X/6X/8X PS/N1 series Tentative Device Specification Fig. 2 Block diagram TDA955X/6X/8X PS/N1 series with QSS IF sound channel AUDEXT RESET VPE LED OUT (2x) SCL SDA VST OUT AUDOUT/AMOUT ADC IN (4x) I/O PORTS (4x) 2000 Jun 22 +3.3 V ENHANCED 1/10 PAGE MEMORY 80C51 CPU VST PWM-DAC I/O PORTS I2C-BUS TRANSCEIVER SOUND PLL DEEMPHASIS AUDIO SWITCH (AVL) VOLUME CONTROL H LUMA DELAY CVBS ROM/RAM PEAKING SYNC PAL/SECAM/NTSC DECODER BASE-BAND DELAY LINE ACQUISITION V TELETEXT TELETEXT/OSD DISPLAY COR R G B BL RO GO BO BCLIN RGB H-DRIVE V-DRIVE + V GEOMETRY 2nd LOOP H-SHIFT RGB/YUV INSERT Y SATURATION U BLACK STRETCH WHITE STRETCH V BLKIN Philips Semiconductors DEEMPHASIS SIF SOUND IF SIFIN AGC AM DEMODULATOR TUNERAGC REF VIFIN VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP. TV signal processor-Teletext decoder with embedded -Controller 8 HOUT V-DRIVE EHTO SOUND TRAP VIDEO SWITCH VIDEO IDENT. REF CVBS/Y C VIDEO FILTERS GROUP DELAY CORRECTION CONTR/BRIGHTN OSD/TEXT INSERT BLUE STRETCH CCC WHITE-P. ADJ. H/V SYNC SEP. +8V H-OSC. + PLL H R/V G/Y B/U BL TDA955X/6X/8X PS/N1 series Tentative Device Specification Fig. 3 Block diagram TDA955X/6X/8X PS/N1 series with QSS IF in AM/FM mode Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller PINNING (GENERAL VERSION) SYMBOL P1.3/T1 P1.6/SCL P1.7/SDA P2.0/TPWM P3.0/ADC0 P3.1/ADC1 P3.2/ADC2 P3.3/ADC3 VSSC/P P0.5 P0.6 VSSA SECPLL VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD /DECSDEM (1) VDRB VDRA IFIN1 IFIN2 IREF VSC AGCOUT AUDEEM/SIFIN1(1) DECSDEM/SIFIN2(1) GND2 SNDPLL/SIFAGC/ (1) AVL/SNDIF/REF0/ AMOUT/AUDEEM(1) HOUT FBISO AUDEXT/QSSO /AMOUT (1) EHTO PLLIF IFVO/SVO VP1 2000 Jun 22 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 TDA955X/6X/8X PS/N1 series DESCRIPTION port 1.3 or Counter/Timer 1 input port 1.6 or I2C-bus clock line port 1.7 or I2C-bus data line port 2.0 or Tuning PWM output port 3.0 or ADC0 input port 3.1 or ADC1 input port 3.2 or ADC2 input port 3.3 or ADC3 input digital ground for -Controller core and periphery port 0.5 (8 mA current sinking capability for direct drive of LEDs) port 0.6 (8 mA current sinking capability for direct drive of LEDs) analog ground of Teletext decoder and digital ground of TV-processor SECAM PLL decoupling 2nd supply voltage TV-processor (+8V) supply voltage of digital circuit of TV-processor phase-2 filter phase-1 filter ground 3 for TV-processor bandgap decoupling Automatic Volume Levelling (90 versions) / E-W drive output (110 versions) / decoupling sound demodulator (QSS version in AM/FM mode) vertical drive B output vertical drive A output IF input 1 IF input 2 reference current input vertical sawtooth capacitor tuner AGC output audio deemphasis or SIF input 1 decoupling sound demodulator or SIF input 2 ground 2 for TV processor narrow band PLL filter or AGC sound IF Automatic Volume Levelling / sound IF input / subcarrier reference output / AM output (non controlled) / audio deemphasis (QSS version in AM/FM mode) horizontal output flyback input/sandcastle output external audio output / QSS intercarrier out / AM audio output (non controlled) EHT/overvoltage protection input IF-PLL loop filter IF video output / selected CVBS output supply voltage TV processor 9 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller SYMBOL CVBS1 GND CVBS/Y C AUDOUT /AMOUT(1) INSSW2 R2/VIN G2/YIN B2/UIN BCLIN BLKIN RO GO BO VDDA VPE VDDC OSCGND XTALIN XTALOUT RESET VDDP P1.0/INT1 P1.1/T0 P1.2/INT0 Note PIN 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 internal CVBS input ground for TV processor CVBS/Y input TDA955X/6X/8X PS/N1 series DESCRIPTION C input audio output /AM audio output (volume controlled) 2nd RGB / YUV insertion input 2nd R input / V (R-Y) input / PR input 2nd G input / Y input 2nd B input / U (B-Y) input / PB input beam current limiter input black current input / V-guard input Red output Green output Blue output analog supply of Teletext decoder and digital supply of TV-processor (3.3 V) OTP Programming Voltage digital supply to core (3.3 V) oscillator ground supply crystal oscillator input crystal oscillator output reset digital supply to periphery (+3.3 V) port 1.0 or external interrupt 1 input port 1.1 or Counter/Timer 0 input port 1.2 or external interrupt 0 input 1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator / QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given in table 1. 2000 Jun 22 10 Table 1 Pin functions for various versions 2000 Jun 22 11 Philips Semiconductors TV signal processor-Teletext decoder with embedded -Controller IC version FM-PLL version QSS VERSION AM/FM MODE (1) NORMAL MODE 0 N 01/10/11 0 1 AVL 00 - Y 01/10/11 0 1 EWD AMFM bit 0 1 East-West Y/N N Y N CMB1/CMB0 bits 00 01/10/11 00 01/10/11 - 00 AM bit - - - - 0 1 - Pin 20 AVL EWD DECSDEM Pin 28 AUDEEM SIFIN1 Pin 29 DECSDEM SIFIN2 Pin 31 SNDPLL SNDPLL SIFAGC(2) (3) (3) REFO REFO AVL/SNDIF AUDEEM/AMOUT AMOUT Pin 32 SNDIF Pin 35 AUDEXT AUDEXT AUDEXT Pin 44 AUDOUT controlled audio out Note SIFIN1 SIFIN2 SIFAGC REFO AMOUT QSSO AMOUT AUDEXT controlled AM out REFO QSSO AMOUT 1. When the AM/FM mode is chosen several pins have a different function. For this reason this mode can be selected only when the adapted application is used. 2. When in the AM/FM mode the AM bit is activated a capacitor with a value of about 2.2 F has to be switched externally in parallel with the sound PLL filter 3. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This function is selected by means of SIF bit in subaddress 21H. TDA955X/6X/8X PS/N1 series Tentative Device Specification Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series P1.3/T1 handbook, halfpage 1 2 3 4 5 6 7 8 9 64 63 62 61 60 59 58 57 56 P1.2/INT0 P1.1/T0 P1.0/INT1 VDDP RESET XTALOUT XTALIN OSCGND VDDC VPE VDDA BO GO RO BLKIN BCLIN B2/UIN G2/YIN R2/VIN INSSW2 AUDOUT/AMOUT C CVBS/Y GND1 CVBS1 VP1 IFVO/SVO PLLIF EHTO AUDEXT/QSSO/ AMOUT FBISO HOUT P1.6/SCL P1.7/SDA P2.0/TPMW P3.0/ADC0 P3.1/ADC1 P3.2/ADC2 P3.3/ADC3 VSSC/P P0.5 P0.6 VSSA SECPLL VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD/ DECSDEM VDRB VDRA IFIN1 IFIN2 IREF VSC AGCOUT AUDEEM/SIFIN1 DECSDEM/SIFIN2 GND2 SNDPLL/SIFAGC AVL/SNDIF/REFO/ AMOUT/AUDEEM/ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 TDA955X/6X/8X PS/N1 series (SDIP-64) 12 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 MXXxxx XXX Fig. 4 Pin configuration (SDIP 64) 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller FUNCTIONAL DESCRIPTION OF THE 80C51 The functionality of the micro-controller used on this device is described here with reference to the industry standard 80C51 micro-controller. A full description of its functionality can be found in the 80C51 based 8-bit micro-controllers - Philips Semiconductors (ref. IC20). Features of the 80c51 * 80C51 micro-controller core standard instruction set and timing. * 1s machine cycle. * Maximum 128K x 8-bit Program ROM. * Maximum of 12K x 8-bit Auxiliary RAM. * 2K (OSD only version) Auxiliary RAM, maximum of 1.25K required for Display * 3K (1 page teletext version) Auxiliary RAM, maximum of 2K required for Display * 12K (10 page teletext version) Auxiliary RAM, maximum of 10K required for Display * 8-Level Interrupt Controller for individual enable/disable with two level priority. * Two 16-bit Timer/Counters. * Additional 16-bit Timer with 8-bit Pre-scaler. * WatchDog Timer. * Auxiliary RAM Page Pointer. * 16-bit Data pointer * Idle, Stand-by and Power-Down modes. * 13 General I/O. * Four 6-bit Pulse Width Modulator (PWM) outputs for control of TV analogue signals. * One 14-bit PWM for Voltage Synthesis tuner control. * 8-bit ADC with 4 multiplexed inputs. * 2 high current outputs for directly driving LED's etc. * I2C Byte Level bus interface. Memory Organisation The device has the capability of a maximum of 128K Bytes of PROGRAM ROM and 12K Bytes of DATA RAM. The OSD (& Closed Caption) only version has a 2K RAM and a maximum of 64K ROM, the 1 page teletext version has a 3K RAM and also a maximum of 64K ROM whilst the 10 page teletext version has a 12K RAM and a maximum of 128K ROM. ROM Organisation The 64K device has a continuous address space from 0 to 64K. The 128K is arranged in four banks of 32K. One of 2000 Jun 22 13 Lower 128 Upper 128 8000H TDA955X/6X/8X PS/N1 series the 32K banks is common and is always addressable. The other three banks (Bank0, Bank1, Bank2) can be accessed by selecting the right bank via the SFR ROMBK bits 1/0. FFFFH Bank0 32K FFFFH Bank1 32K FFFFH Bank2 32K 8000H 8000H 7FFFH Common 32K 0000H Fig.5 ROM Bank Switching memory map RAM Organisation The Internal Data RAM is organised into two areas, Data Memory and Special Function Registers (SFRs) as shown in Fig.6. FFH Accessible by Indirect Addressing only 80H 7FH Accessible by Direct and Indirect Addressing 00H Data Memory Special Function Registers Accessible by Direct Addressing only Fig.6 Internal Data Memory DATA MEMORY The Data memory is 256 x 8-bits and occupies the address range 00 to FF Hex when using Indirect addressing and 00 to 7F Hex when using direct addressing. The SFRs occupy the address range 80 Hex to FF Hex and are accessible using Direct addressing only. The lower 128 Bytes of Data memory are mapped as shown in Fig.7. The lowest 32 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series bytes are grouped into 4 banks of 8 registers, the next 16 bytes above the register banks form a block of bit addressable memory space. The upper 128 bytes are not allocated for any special area or functions. 7FH 2FH Bank Select Bits in PSW 20H 1FH 11 = BANK3 18H 17H 10 = BANK2 10H 0FH 01 = BANK1 08H 07H 00 = BANK0 00H Fig.7 Lower 128 Bytes of Internal RAM SFR MEMORY The Special Function Register (SFR) space is used for port latches, counters/timers, peripheral control, data capture and display. These registers can only be accessed by direct addressing. Sixteen of the addresses in the SFR space are both bit and byte addressable. The bit addressable SFRs are those whose address ends in 0H or 8H. A summary of the SFR map in address order is shown in Table 2. ADD 80H 81H 82H 83H 84H 85H 87H 88H 89H 8AH 8BH 8CH 8DH 90H 91H R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Names P0 SP DPL DPH IEN1 IP1 PCON TCON TMOD TL0 TL1 TH0 TH1 P1 TP2L BIT7 Reserved SP<7> DPL<7> DPH<7> 0 TF1 GATE TL0<7> TL1<7> TH0<7> TH1<7> P1<7> TP2L<7> BIT6 P0<6> SP<6> DPL<6> DPH<6> ARD TR1 C/T TL0<6> TL1<6> TH0<6> TH1<6> P1<6> TP2L<6> BIT5 P0<5> SP<5> DPL<5> DPH<5> RFI TF0 M1 TL0<5> TL1<5> TH0<5> TH1<5> Reserved TP2L<5> BIT4 Reserved SP<4> DPL<4> DPH<4> WLE TR0 M0 TL0<4> TL1<4> TH0<4> TH1<4> Reserved TP2L<4> 4 Banks of 8 Registers R0 - R7 Bit Addressable Space (Bit Addresses 0-7F) BIT3 Reserved SP<3> DPL<3> DPH<3> GF1 IE1 GATE TL0<3> TL1<3> TH0<3> TH1<3> P1<3> TP2L<3> BIT2 Reserved SP<2> DPL<2> DPH<2> GF0 IT1 C/T TL0<2> TL1<2> TH0<2> TH1<2> P1<2> TP2L<2> BIT1 Reserved SP<1> DPL<1> DPH<1> PD IE0 M1 TL0<1> TL1<1> TH0<1> TH1<1> P1<1> TP2L<1> BIT0 Reserved SP<0> DPL<0> DPH<0> ET2 PT2 IDL IT0 M0 TL0<0> TL1<0> TH0<0> TH1<0> P1<0> TP2L<0> Table 2 SFR Map 2000 Jun 22 14 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller ADD 92H 93H 94H 96H 97H 98H 9CH 9DH 9EH 9FH A0H A6H A7H A8H B0H B2H B3H B4H R/W R/W R/W R/W R/W R/W R/W R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Names TP2H TP2PR TP2CRL P0CFGA P0CFGB SADB TP2CL TP2CH P1CFGA P1CFGB P2 P2CFGA P2CFGB IE P3 TXT18 TXT19 TXT20 BIT7 TP2H<15> TP2PR<7> Reserved Reserved TP2CL<7> TP2CH<7> P1CFGA<7> TDA955X/6X/8X PS/N1 series BIT6 TP2H<14> TP2PR<6> P0CFGA<6> BIT5 TP2H<13> TP2PR<5> P0CFGA<5> BIT4 TP2H<12> TP2PR<4> Reserved Reserved DC_COMP TP2CL<4> TP2CH<4> Reserved Reserved P2CFGA<4> BIT3 TP2H<11> TP2PR<3> Reserved Reserved SAD<3> TP2CL<3> TP2CH<3> P1CFGA<3> BIT2 TP2H<10> TP2PR<2> Reserved Reserved SAD<2> TP2CL<2> TP2CH<2> P1CFGA<2> BIT1 TP2H<9> TP2PR<1> TP2CRL<1> Reserved Reserved SAD<1> TP2CL<1> TP2CH<1> P1CFGA<1> BIT0 TP2H<8> TP2PR<0> TP2CRL<0> Reserved Reserved SAD<0> TP2CL<0> TP2CH<0> P1CFGA<0> P0CFGB<6> TP2CL<6> TP2CH<6> P1CFGA<6> P0CFGB<5> TP2CL<5> TP2CH<5> Reserved Reserved P2CFGA<5> P1CFGB<7> Reserved Reserved Reserved EA Reserved NOT<3> TEN DRCS ENABLE DISP LINE<1> GPF1<7> 0 0 0 P1CFGB<6> P2CFGA<6> P1CFGB<3> P2CFGA<3> P1CFGB<2> P2CFGA<2> P1CFGB<1> P2CFGA<1> P1CFGB<0> P2<0> P2CFGA<0> P2CFGB<6> EBUSY Reserved NOT<2> TC<2> OSD PLANES DISP LINES<0> GPF1<6> 0 PBUSY FORCE ACQ<1> 0 P2CFGB<5> ES2 Reserved NOT<1> TC<1> 0 P2CFGB<4> ECC Reserved NOT<0> TC<0> 0 P2CFGB<3> ET1 P3<3> 0 0 OSD LANG ENABLE Reserved P2CFGB<2> EX1 P3<2> 0 0 OSD LAN<2> CC ON P2CFGB<1> ET0 P3<1> BS<1> TS<1> OSD LAN<1> I2C PORT0 P2CFGB<0> EX0 P3<0> BS<0> TS<0> OSD LAN<0> CC/TXT B5H R/W TXT21 CHAR SIZE<1> GPF1<5> 0 PES2 FORCE ACQ<0> 0 CHAR SIZE<0> GPF1<4> CS<4> PCC FORCE DISP<1> WSS<3:0> ERROR WSS<7:4> ERROR WSS<11> B6H B7H B8H B9H R R/W R/W R/W TXT22 CCLIN IP TXT17 GPF1<3> CS<3> PT1 FORCE DISP<0> WSS<3> GPF1<2> CS<2> PX1 SCREEN COL<2> WSS<2> GPF1<1> CS<1> PT0 SCREEN COL<1> WSS<1> GPF1<0> CS<0> PX0 SCREEN COL<0> WSS<0> BAH R WSS1 0 BBH R WSS2 0 0 0 WSS<7> WSS<6> WSS<5> WSS<4> BCH R WSS3 WSS<13:11> ERROR WSS<13> WSS<12> WSS<10:8> ERROR P3CFGA<3> WSS<10> WSS<9> WSS<8> BEH BFH C0H R/W R/W R/W P3CFGA P3CFGB TXT0 Reserved Reserved X24 POSN Reserved Reserved DISPLAY X24 Reserved Reserved AUTO FRAME Reserved Reserved DISABLE HEADER ROLL P3CFGA<2> P3CFGA<1> P3CFGA<0> P3CFGB<3> DISPLAY STATUS ROW ONLY P3CFGB<2> DISABLE FRAME P3CFGB<1> VPS ON P3CFGB<0> INV ON Table 2 SFR Map 2000 Jun 22 15 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller ADD C1H R/W R/W Names TXT1 BIT7 EXT PKT OFF ACQ BANK OSD BANK ENABLE BIT6 8 BIT BIT5 ACQ OFF BIT4 X26 OFF TDA955X/6X/8X PS/N1 series BIT3 FULL FIELD REQ<0> PRD<3> B MESH ENABLE BIT2 FIELD POLARITY SC<2> PRD<2> C MESH ENABLE BIT1 H POLARITY SC<1> PRD<1> TRANS ENABLE BIT0 V POLARITY SC<0> PRD<0> SHADOW ENABLE C2H C3H C4H R/W W R/W TXT2 TXT3 TXT4 REQ<3> QUAD WIDTH ENABLE BKGND IN REQ<2> EAST/WES T REQ<1> PRD<4> DISABLE DOUBLE HEIGHT CORB IN C5H R/W TXT5 BKGND OUT BKGND OUT STATUS ROW TOP (Reserved) 0 CURSOR FREEZE 0 D<7> 525/625 SYNC CORB OUT TEXT OUT TEXT IN PICTURE ON OUT PICTURE ON OUT BOX ON 1-23 WSS ON PICTURE ON IN PICTURE ON IN BOX ON 0 C6H R/W TXT6 BKGND IN CORB OUT CORB IN TEXT OUT TEXT IN C7H R/W TXT7 CURSOR ON FLICKER STOP ON CLEAR MEMORY 0 D<6> ROM VER<4> REVEAL BOTTOM/ TOP DISABLE SPANISH R<4> DOUBLE HEIGHT PKT 26 RECEIVED R<3> BOX ON 24 C8H R/W TXT8 HUNT WSS RECEIVED R<2> CVBS1/ CVBS0 R<0> C9H R/W TXT9 A0 R<1> CAH CBH CCH R/W R/W R TXT10 TXT11 TXT12 C<5> D<5> ROM VER<3> C<4> D<4> ROM VER<2> C<3> D<3> ROM VER<1> C<2> D<2> ROM VER<0> C<1> D<1> 1 C<0> D<0> VIDEO SIGNAL QUALITY PAGE<0> CDH R/W TXT14 0 0 0 DISPLAY BANK MICRO BANK RS1 TD<4> TD<12> PW0V<4> PW1V<4> CCD1<4> STO STAT<1> DAT<4> ADR<3> PW3V<4> ACC<4> PW2V<4> PAGE<3> PAGE<2> PAGE<1> CEH R/W TXT15 0 0 0 BLOCK<3> BLOCK<2> BLOCK<1> BLOCK<0> D0H D2H D3H D5H D6H D7H D8H D9H DAH DBH DCH E0H E4H R/W R/W R/W R/W R/W R R/W R R/W R/W R/W R/W R/W PSW TDACL TDACH PWM0 PWM1 CCDAT1 S1CON S1STA S1DAT S1ADR PWM3 ACC PWM2 C TD<7> TPWE PW0E PW1E CCD1<7> CR<2> STAT<4> DAT<7> ADR<6> PW3E ACC<7> PW2E AC TD<6> 1 1 1 CCD1<6> ENSI STAT<3> DAT<6> ADR<5> 1 ACC<6> 1 F0 TD<5> TD<13> PW0V<5> PW1V<5> CCD1<5> STA STAT<2> DAT<5> ADR<4> PW3V<5> ACC<5> PW2V<5> RS0 TD<3> TD<11> PW0V<3> PW1V<3> CCD1<3> SI STAT<0> DAT<3> ADR<2> PW3V<3> ACC<3> PW2V<3> OV TD<2> TD<10> PW0V<2> PW1V<2> CCD1<2> AA 0 DAT<2> ADR<1> PW3V<2> ACC<2> PW2V<2> TD<1> TD<9> PW0V<1> PW1V<1> CCD1<1> CR<1> 0 DAT<1> ADR<0> PW3V<1> ACC<1> PW2V<1> P TD<0> TD<8> PW0V<0> PW1V<0> CCD1<0> CR<0> 0 DAT<0> GC PW3V<0> ACC<0> PW2V<0> Table 2 SFR Map 2000 Jun 22 16 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller ADD E7H E8H F0H F8H R/W R R/W R/W R/W Names CCDAT2 SAD B TXT13 BIT7 CCD2<7> VHI B<7> VPS RECEIVED XRAMP<7> STANDBY TEST<7> WKEY<7> WDV<7> BIT6 CCD2<6> CH<1> B<6> PAGE CLEARING XRAMP<6> IIC_LUT<1> TDA955X/6X/8X PS/N1 series BIT5 CCD2<5> CH<0> B<5> 525 DISPLAY XRAMP<5> IIC_LUT<0> BIT4 CCD2<4> ST B<4> 525 TEXT BIT3 CCD2<3> SAD<7> B<3> 625 TEXT BIT2 CCD2<2> SAD<6> B<2> PKT 8/30 BIT1 CCD2<1> SAD<5> B<1> FASTEXT BIT0 CCD2<0> SAD<4> B<0> 0 FAH FBH FDH FEH FFH R/W R/W R W R/W XRAMP ROMBK TEST WDTKEY WDT XRAMP<4> 0 TEST<4> WKEY<4> WDV<4> XRAMP<3> 0 TEST<3> WKEY<3> WDV<3> XRAMP<2> 0 TEST<2> WKEY<2> WDV<2> XRAMP<1> ROMBK<1> TEST<1> WKEY<1> WDV<1> XRAMP<0> ROMBK<0> TEST<0> WKEY<0> WDV<0> TEST<6> WKEY<6> WDV<6> TEST<5> WKEY<5> WDV<5> Table 2 SFR Map A description of each of the SFR bits is shown in Table 3, The SFRs are in alphabetical order. Names ACC ACC<7:0> B B<7:0> CCDAT1 CCD1<7:0> CCDAT2 CCD2<7:0> CCLIN CS<4:0> DPH DPH<7:0> DPL DPL<7:0> IE EA EBUSY ES2 ECC BIT7 ACC<7> BIT6 ACC<6> BIT5 ACC<5> BIT4 ACC<4> BIT3 ACC<3> BIT2 ACC<2> BIT1 ACC<1> BIT0 ACC<0> RESET 00H Accumulator value. B<7> B Register value. CCD1<7> CCD1<6> CCD1<5> CCD1<4> CCD1<3> CCD1<2> CCD1<1> CCD1<0> 00H B<6> B<5> B<4> B<3> B<2> B<1> B<0> 00H Closed Caption first data byte. CCD2<7> CCD2<6> CCD2<5> CCD2<4> CCD2<3> CCD2<2> CCD2<1> CCD2<0> 00H Closed Caption second data byte. 0 0 0 CS<4> CS<3> CS<2> CS<1> CS<0> 15H Closed Caption Slice line using 525 line number. DPH<7> DPH<6> DPH<5> DPH<4> DPH<3> DPH<2> DPH<1> DPH<0> 00H Data Pointer High byte, used with DPL to address display and auxiliary memory. DPL<7> DPL<6> DPL<5> DPL<4> DPL<3> DPL<2> DPL<1> DPL<0> 00H Data pointer low byte, used with DPH to address display and auxiliary memory. EA EBUSY ES2 ECC ET1 EX1 ET0 EX0 00H Disable all interrupts (0), or use individual interrupt enable bits (1). Enable BUSY Interrupt. Enable I2C Interrupt. Enable Closed Caption Interrupt. Table 3 SFR Bit description 2000 Jun 22 17 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names ET1 EX1 ET0 EX0 IEN1 ET2 IP PBUSY PES2 PCC PT1 PX1 PT0 PX0 IP1 PT2 P0 P0<6:5> P1 P1<7:6> P1<3:0> P2 P2<6:0> P3 P3<3:0> P0CFGA P0CFGB BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET Enable Timer 1 Interrupt. Enable External Interrupt 1. Enable Timer 0 Interrupt. Enable External Interrupt 0. ET2 00H Enable Timer 2 Interrupt. 0 PBUSY PES2 PCC PT1 PX1 PT0 PX0 00H Priority EBUSY Interrupt. Priority ES2 Interrupt. Priority ECC Interrupt. Priority Timer 1 Interrupt. Priority External Interrupt 1. Priority Timer 0 Interrupt. Priority External Interrupt 0. PT2 00H Priority Timer 2 Interrupt. Reserved P0<6> P0<5> Reserved Reserved Reserved Reserved Reserved FFH Port 0 I/O register connected to external pins. P1<7> P1<6> Reserved Reserved P1<3> P1<2> P1<1> P1<0> FFH Port 1 I/O register connected to external pins. Port 1 I/O register connected to external pins. Reserved P2<6> P2<5> P2<4> P2<3> P2<2> P2<1> P2<0> FFH Port 2 I/O register connected to external pins. Reserved Reserved Reserved Reserved P3<3> P3<2> P3<1> P3<0> FFH Port 3 I/O register connected to external pins. Reserved Reserved P0CFGA<6> P0CFGB<6> P0CFGA<5> P0CFGB<5> Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved FFH 00H P0CFGB P1CFGA<7> P1CFGB<7> MODE 0 Open Drain. MODE 1 Quasi Bi-Directional. MODE2 High Impedance. MODE3 Push Pull. P1CFGA<6> P1CFGB<6> Reserved Reserved Reserved Reserved P1CFGA<3> P1CFGB<3> P1CFGA<2> P1CFGB<2> P1CFGA<1> P1CFGB<1> P1CFGA<0> P1CFGB<0> FFH 00H Table 3 SFR Bit description 18 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET P1CFGB MODE 0 Open Drain. MODE 1 Quasi Bi-Directional. MODE2 High Impedance. MODE3 Push Pull. P2CFGA<6> P2CFGB<6> P2CFGA<5> P2CFGB<5> P2CFGA<4> P2CFGB<4> P2CFGA<3> P2CFGB<3> P2CFGA<2> P2CFGB<2> P2CFGA<1> P2CFGB<1> P2CFGA<0> P2CFGB<0> FFH 00H P2CFGB MODE 0 Open Drain. MODE 1 Quasi Bi-Directional. MODE2 High Impedance. MODE3 Push Pull. Reserved Reserved Reserved Reserved Reserved Reserved P3CFGA<3> P3CFGB<3> P3CFGA<2> P3CFGB<2> P3CFGA<1> P3CFGB<1> P3CFGA<0> P3CFGB<0> FFH 00H P3CFGB MODE 0 Open Drain. MODE 1 Quasi Bi-directional. MODE2 High Impedance. MODE3 Push Pull. ARD RFI WLE GF1 GF0 PD IDL 00H UART Baud Rate Double Control. Auxiliary RAM Disable, All MOVX instructions access the external data memory. Disable ALE during internal access to reduce Radio Frequency Interference. Watch Dog Timer enable. General purpose flag. General purpose flag. Power-down activation bit. Idle mode activation bit. C Carry Bit. Auxiliary Carry bit. Flag 0, General purpose flag. Register Bank selector bits. RS<1:0> = 00, Bank0 (00H - 07H). RS<1:0> = 01, Bank1 (08H - 0FH). RS<1:0> = 10, Bank2 (10H - 17H). RS<1:0> = 11, Bank3 (18H - 1FH). AC F0 RS<1> RS<0> OV P 00H OV Overflow flag. Table 3 SFR Bit description 19 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names P PWM0 PW0E BIT7 Parity bit. PW0E 1 PW0V<5> PW0V<4> PW0V<3> BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET PW0V<2> PW0V<1> PW0V<0> 40H 0 - Disable Pulse Width Modulator 0. 1 - Enable Pulse Width Modulator 0. Pulse Width Modulator high time. PW1E 1 PW1V<5> PW1V<4> PW1V<3> PW1V<2> PW1V<1> PW1V<0> 40H PW0V<5:0> PWM1 PW1E 0 - Disable Pulse Width Modulator 1. 1 - Enable Pulse Width Modulator 1. Pulse Width Modulator high time. PW2E 1 PW2V<5> PW2V<4> PW2V<3> PW2V<2> PW2V<1> PW2V<0> 40H PW1V<5:0> PWM2 PW2E 0 - Disable Pulse Width Modulator 2. 1 - Enable Pulse Width Modulator 2. Pulse Width Modulator high time. PW3E 1 PW3V<5> PW3V<4> PW3V<3> PW3V<2> PW3V<1> PW3V<0> 40H PW2V<5:0> PWM3 PW3E 0 - Disable Pulse Width Modulator 3. 1 - Enable Pulse Width Modulator 3. Pulse Width Modulator high time. STANDBY IIC_LUT<1> IIC_LUT<0> PW3V<5:0> ROMBK STANDBY 0 0 0 ROMBK<1> ROMBK<0> 00H 0 - Disable Stand-by Mode 1 - Enable Stand-by Mode IIC Lookup table selection: IIC_LUT<1:0>=00, 558 Normal Mode. IIC_LUT<1:0>=01, 558 Fast Mode. IIC_LUT<1:0>=10, 558 Slow Mode. IIC_LUT<1:0>=11, Reserved. ROM Bank selection ROMBK<1:0>=00, Bank0 ROMBK<1:0>=01, Bank1 ROMBK<1:0>=10, Bank2 ROMBK<1:0>=11, Reserved IIC_LUT<1:0> ROMBK<1:0> S1ADR ADR<6:0> GC ADR<6> ADR<5> ADR<4> ADR<3> ADR<2> ADR<1> ADR<0> GC 00H I2C Slave Address. 0 - Disable I2C general call address. 1 - Enable I2C general call address. CR<2> ENSI STA STO SI AA CR<1> CR<0> 00H S1CON CR<2:0> Clock rate bits. IIC rates are selectable (three tables) 0 - Disable I2C interface. 1 - Enable I2C interface. ENSI Table 3 SFR Bit description 2000 Jun 22 20 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names STA BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET START flag. When this bit is set in slave mode, the hardware checks the I2C bus and generates a START condition if the bus is free or after the bus becomes free. If the device operates in master mode it will generate a repeated START condition. STOP flag. If this bit is set in a master mode a STOP condition is generated. A STOP condition detected on the I2C bus clears this bit. This bit may also be set in slave mode in order to recover from an error condition. In this case no STOP condition is generated to the I2C bus, but the hardware releases the SDA and SCL lines and switches to the not selected receiver mode. The STOP flag is cleared by the hardware. Serial Interrupt flag. This flag is set and an interrupt request is generated, after any of the following events occur: -A START condition is generated in master mode. -The own slave address has been received during AA=1. -The general call address has been received while S1ADR.GC and AA=1. -A data byte has been received or transmitted in master mode (even if arbitration is lost). -A data byte has been received or transmitted as selected slave. A STOP or START condition is received as selected slave receiver or transmitter While the SI flag is set, SCL remains LOW and the serial transfer is suspened.SI must be reset by software. Assert Acknowledge flag. When this bit is set, an acknowledge is returned after any one of the following conditions -Own slave address is received. -General call address is received(S1ADR.GC=1). -A data byte is received, while the device is programmed to be a master receiver. -A data byte is received, while the device is selected slave receiver. When the bit is reset, no acknowledge is returned. Consequently, no interrupt is requested when the own address or general call address is received. DAT<7> DAT<6> DAT<5> DAT<4> DAT<3> DAT<2> DAT<1> DAT<0> 00H STO SI AA S1DAT DAT<7:0> S1STA STAT<4:0> SAD VHI I2C Data. STAT<4> STAT<3> STAT<2> STAT<1> STAT<0> 0 0 0 F8H I2C Interface Status. VHI CH<1> CH<0> ST SAD<7> SAD<6> SAD<5> SAD<4> 00H 0 - Analogue input voltage less than or equal to DAC voltage. 1 - Analogue input voltage greater then DAC voltage. ADC Input channel select. CH<1:0> = 00,ADC3. CH<1:0> = 01,ADC0. CH<1:0> = 10,ADC1. CH<1:0> = 11,ADC2. Initiate voltage comparison between ADC input Channel and SADB<3:0> value. Note: Set by Software and reset by Hardware. Most Significant nibble of DAC input word 0 0 0 DC_COMP SAD<3> SAD<2> SAD<1> SAD<0> 00H CH<1:0> ST SAD<7:4> SADB DC_COMP 0 - Disable DC Comparator mode. 1 - Enable DC Comparator mode. 4-bit SAD value. SP<7> SP<6> SP<5> SP<4> SP<3> SP<2> SP<1> SP<0> 07H SAD<3:0> SP SP<7> TCON TF1 Stack Pointer. TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H Timer 1 overflow Flag. Set by hardware on Timer/Counter overflow.Cleared by hardware when processor vectors to interrupt routine. Table 3 SFR Bit description 21 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names TR1 TF0 TR0 IE1 BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET Timer 1 Run control bit. Set/Cleared by software to turn Timer/Counter on/off. Timer 0 overflow Flag. Set by hardware on Timer/Counter overflow.Cleared by hardware when processor vectors to interrupt routine. Timer 0 Run control bit. Set/Cleared by software to turn Timer/Counter on/off. Interrupt 1 Edge flag (both edges generate flag). Set by hardware when external interrupt edge detected.Cleared by hardware when interrupt processed. Interrupt 1 Type control bit. Set/Cleared by Software to specify edge/low level triggered external interrupts. Interrupt 0 Edge l flag. Set by hardware when external interrupt edge detected.Cleared by hardware when interrupt processed. Interrupt 0 Type flag.Set/Cleared by Software to specify falling edge/low level triggered external interrupts. TPWE 1 TD<13> TD<12> TD<11> TD<10> TD<9> TD<8> 40H IT1 IE0 IT0 TDACH TPWE 0 - Disable Tuning Pulse Width Modulator. 1 - Enable Tuning Pulse Width Modulator. Tuning Pulse Width Modulator High Byte. TD<7> TD<6> TD<5> TD<4> TD<3> TD<2> TD<1> TD<0> 00H TD<13:8> TDACL TD<7:0> TH0 TH0<7:0> TH1 TH1<7:0> TL0 TL0<7:0> TL1 TL1<7:0> TMOD Tuning Pulse Width Modulator Low Byte. TH0<7> Timer 0 high byte. TH1<7> Timer 1 high byte. TL0<7> Timer 0 low byte. TL1<7> Timer 1 low byte. GATE C/T M1 M0 GATE C/T M1 M0 00H TL1<6> TL1<5> TL1<4> TL1<3> TL1<2> TL1<1> TL1<0> 00H TL0<6> TL0<5> TL0<4> TL0<3> TL0<2> TL0<1> TL0<0> 00H TH1<6> TH1<5> TH1<4> TH1<3> TH1<2> TH1<1> TH1<0> 00H TH0<6> TH0<5> TH0<4> TH0<3> TH0<2> TH0<1> TH0<0> 00H Timer / Counter 1 GATE C/T M1,M0 Gating Control Timer /Counter 1. Counter/Timer 1 selector. Mode control bits Timer/Counter 1. M1,M0 = 00, 8 bit timer or 8 bit counter with divide by 32 pre-scaler. Timer / Counter 0 M1,M0 = 01, 16 bit time interval or event counter. M1,M0 = 10, 8 bit time interval or event counter with automatic reload upon overflow. Reload value stored in TH1. M1,M0 = 11, stopped. GATE C/T Gating control Timer/Counter 0. Counter/Timer 0 selector. Table 3 SFR Bit description 2000 Jun 22 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names M1,M0 BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET Mode Control bits Timer/Counter 0. M1,M0 = 00, 8 bit timer or 8 bit counter with divide by 32 pre-scaler. M1,M0 = 01, 16 bit time interval or event counter. M1,M0 = 10, 8 bit time interval or event counter with automatic reload upon overflow. Reload value stored in TH0. M1,M0 = 11, one 8 bit time interval or event counter and one 8 bit time interval counter. TP2CL<7> TP2CL<6> TP2CL<5> TP2CL<4> TP2CL<3> TP2CL<2> TP2CL<1> TP2CL<0> 00H TP2CL TP2CL<7:0> TP2CH TP2CH<7:0> TP2H TP2H<7:0> TP2L TP2L<7:0> TP2PR TP2H<7:0> TP2CRL TP2CRL<0> Indicate the low byte of the Time 2 current value. TP2CH<7> TP2CH<6> TP2CH<5> TP2CH<4> TP2CH<3> TP2CH<2> TP2CH<1> TP2CH<0> 00H Indicate the high byte of the Time 2 current value. TP2H<7> TP2H<6> TP2H<5> TP2H<4> TP2H<3> TP2H<2> TP2H<1> TP2H<0> 00H Timer 2 high byte, never change unless updated by the software. TP2L<7> TP2L<6> TP2L<5> TP2L<4> TP2L<3> TP2L<2> TP2L<1> TP2L<0> 00H Timer 2 low byte, never change unless updated by the software. TP2PR<7> TP2PR<6> TP2PR<5> TP2PR<4> TP2PR<3> TP2PR<2> TP2PR<1> TP2PR<0> 00H Timer 2 Pre-scaler, never change unless updated by the software. Timer 2 Control. 0 - Timer 2 disabled. 1 - Timer 2 enabled. Timer 2 Status. 0 - No Overflow. 1 - Overflow. TEST<7> TEST<6> TEST<5> TEST<4> TEST<3> TEST<2> TEST<1> TEST<0> 00H TP2CRL<1> TP2CRL<0> 00H TP2CRL<1> TEST TEST<2:0> Program Type bit SEL<2:0>. 011 - Display Dram test. 001 - Acquisition1 test. 010 - Acquisition2 test Functional test mode bits, set via mode select logic. Dram Size. 000 - 1.5K x 16. 001 - 2K x 16. 010 - 6K x 16. 011 - 7K x 16. 100 - 12K x 16. 101 - 14K x 16. 110 - 1K x 16. 111 - 11K x 16. TEST<4:3> TEST<7:5> TXT0 X24 POSN DISPLAY X24 AUTO FRAME DISABLE HEADER ROLL DISPLAY STATUS ROW ONLY DISABLE FRAME VPS ON INV ON 00H X24 POSN 0 - Store X/24 in extension memory 1 - Store X/24 in basic page memory with packets 0 to 23 Table 3 SFR Bit description 23 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names DISLAY X24 BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET 0 - Display row 24 from basic page memory 1 - Display row 24 from appropriate location in extension memory 0 - Normal Frame output 1 - Frame output is switched off automatically if any video displayed 0 - Write rolling headers and time to current display page 1 - Disable writing of rolling headers and time to into memory 0 - Display normal page rows 0 to 24 1- Display only row 24 0 - Normal Frame output 1 - Force Frame output to be low (0) 0 - VPS acquisition off 1 - VPS acquisition on 0 - Inventory page off 1 - Inventory page on EXT PKT OFF 8 BIT ACQ OFF ACQ OFF FULL FIELD FIELD POLARITY H POLARITY V POLARITY 00H AUTO FRAME DISABLE HEADER ROLL DISPLAY STATUS ROW ONLY DISABLE FRAME VPS ON INV ON TXT1 EXT PKT OFF 0 - Acquire extension packets X/24,X/27,8/30/X 1 - Disable acquisition of extension packets 0 - Error check and/or correct packets 0 to 24 1 - Disable checking of packets 0 to 24 written into memory 0 - Write requested data into display memory 1 - Disable writing of data into Display memory 0 - Enable automatic processing of X/26 data 1 - Disable automatic processing of X/26 data 0 - Acquire CC data only on selected line. 1 - Acquire CC data on any TV line (for test purposes). 0 - Vsync pulse in first half of line during even field. 1 - Vsync pulse in second half of line during even field. 8 BIT ACQ OFF X26 OFF FULL FIELD FIELD POLARIY H POLARITY 0 - Hsync reference edge is positive going 1 - Hsync reference edge is negative going 0 - Vsync reference edge is positive going 1 - Vsync reference edge is negative going ACQ BANK REQ<3> REQ<2> REQ<1> REQ<0> SC<2> SC<1> SC<0> 00H V POLARITY TXT2 ACQ_BANK 0 - Select Acquisition bank 0 1 - Select Acquisition bank 1 Page request Start column of page request PRD<4> PRD<3> PRD<2> PRD<1> PRD<0> 00H REQ<3:0> SC<2:0> TXT3 PRD<4:0> Page Request data Table 3 SFR Bit description 2000 Jun 22 24 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names TXT4 BIT7 OSD BANK ENABLE BIT6 QUAD WIDTH ENABLE BIT5 EAST/WEST TDA955X/6X/8X PS/N1 series BIT4 DISABLE DBL HEIGHT BIT3 B MESH ENABLE BIT2 C MESH ENABLE BIT1 TRANS ENABLE BIT0 SHADOW ENABLE RESET 00H OSD BANK ENABLE QUAD WIDTH ENABLE EAST/WEST 0 - Only alpha numeric OSD characters available, 32 locations 1 - Alternate OSD location available via graphic attribute, additional 32 location 0 - Disable display of Quadruple width characters 1 - Enable display of Quadruple width characters 0 - Western language selection of character codes A0 to FF 1 - Eastern character selection of character codes A0 to FF 0 - Allow normal decoding of double height characters 1 - Disable normal decoding of double height characters 0 - Normal display of black background 1 - Enable meshing of black background 0 - normal display of coloured background 1 - Enable meshing of coloured background 0 - Display black background as normal 1 - Display black background as video 0 - Disable display of shadow/fringing 1 - Display shadow/ fringe (default SE black) BKGND OUT BKGND IN COR OUT COR IN TEXT OUT TEXT IN PICTURE ON OUT PICTURE ON IN 03H DISABLE DOUBLE HEIGHT B MESH ENABLE C MESH ENABLE TRANS ENABLE SHADOW ENABLE TXT5 BKGND OUT 0 - Background colour not displayed outside teletext boxes 1 - Background colour displayed outside teletext boxes 0 - Background colour not displayed inside teletext boxes 1 - Background colour displayed inside teletext boxes 0 - COR not active outside teletext and OSD boxes 1 - COR active outside teletext and OSD boxes 0 - COR not active inside teletext and OSD boxes 1 - COR active inside teletext and OSD boxes BKGND IN COR OUT COR IN TEXT OUT 0 - TEXT not displayed outside teletext boxes 1 - TEXT displayed outside teletext boxes 0 - TEXT not displayed inside teletext boxes 1 - TEXT displayed inside teletext boxes 0 - VIDEO not displayed outside teletext boxes 1 - VIDEO displayed outside teletext boxes 0 - VIDEO not displayed inside teletext boxes 1 - VIDEO displayed inside teletext boxes TEXT IN PICTURE ON OUT PICTURE ON IN TXT6 BKGND OUT BKGND IN COR OUT COR IN TEXT OUT TEXT IN PICTURE ON OUT PICTURE ON IN 03H BKGND OUT 0 - Background colour not displayed outside teletext boxes 1 - Background colour displayed outside teletext boxes Table 3 SFR Bit description 2000 Jun 22 25 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names BKGND IN BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET 0 - Background colour not displayed inside teletext boxes 1 - Background colour displayed inside teletext boxes 0 - COR not active outside teletext and OSD boxes 1 - COR active outside teletext and OSD boxes 0 - COR not active inside teletext and OSD boxes 1 - COR active inside teletext and OSD boxes 0 - TEXT not displayed outside teletext boxes 1 - TEXT displayed outside teletext boxes 0 - TEXT not displayed inside teletext boxes 1 - TEXT displayed inside teletext boxes 0 - VIDEO not displayed outside teletext boxes 1 - VIDEO displayed outside teletext boxes 0 - VIDEO not displayed inside teletext boxes 1 - VIDEO displayed inside teletext boxes STATUS ROW TOP CURSOR ON REVEAL BOTTOM/ TOP DOUBLE HEIGHT BOX ON 24 BOX ON 1-23 BOX ON 0 00H COR OUT COR IN TEXT OUT TEXT IN PICTURE ON OUT PICTURE ON IN TXT7 STATUS ROW TOP CURSOR ON 0 - Display memory row 24 information below teletext page (on display row 24) 1 - Display memory row 24 information above teletext page (on display row 0) 0 - Disable display of cursor 1 - Display cursor at position given by TXT9 and TXT10 0 - Display as spaces characters in area with conceal attribute set 1 - Display characters in area with conceal attribute set 0 - Display memory rows 0 to 11 when double height bit is set 1 - Display memory rows 12 to 23 when double height bit is set 0 - Display each characters with normal height 1 - Display each character as twice normal height. 0 - Disable display of teletext boxes in memory row 24 1 - Enable display of teletext boxes in memory row 24 0 - Disable display of teletext boxes in memory row 1 to 23 1 - Enable display of teletext boxes in memory row 1 to 23 0 - Disable display of teletext boxes in memory row 0 1 - Enable display of teletext boxes in memory row 0 (Reserved) 0 FLICKER STOP ON HUNT DISABLE SPANISH PKT 26 RECEIVED WSS RECEIVED WSS ON (Reserved) 0 00H REVEAL BOTTOM/TOP DOUBLE HEIGHT BOX ON 24 BOX ON 1-23 BOX ON 0 TXT8 FLICKER STOP ON HUNT 0 - Enable `Flicker Stopper' circuitry 1 - Disable `Flicker Stopper' circuitry 0 - Allow automatic hunting for amplitude of data to be acquired 1 - Disable automatic hunting for amplitude 0 - Enable special treatment of Spanish packet 26 characters 1 - Disable special treatment of Spanish packet 26 characters DISABLE SPANISH Table 3 SFR Bit description 2000 Jun 22 26 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names PKT 26 RECEIVED BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET 0 - No packet 26 data has been processed 1 - Packet 26 data has been processed. Note: This flag is set by Hardware and must be reset by Software 0 - No Wide Screen Signalling data has been processed 1 - Wide Screen signalling data has been processed Note: This flag is set by Hardware and must be reset by Software. 0 - Disable acquisition of WSS data. 1 - Enable acquisition of WSS data. CURSOR FREEZE CLEAR MEMORY A0 R<4> R<3> R<2> R<1> R<0> 00H WSS RECEIVED WSS ON TXT9 CURSOR FREEZE CLEAR MEMORY 0 - Use current TXT9 and TXT10 values for cursor position. 1 - Lock cursor at current position 01 - Clear memory block pointed to by TXT15 Note: This flag is set by Software and reset by Hardware 0 - Access memory block pointed to by TXT15 1 - Access extension packet memory Current memory ROW value. Note: Valid range TXT mode 0 to 24, CC mode 0 to 15 0 0 C<5> C<4> C<3> C<2> C<1> C<0> 00H A0 R<4:0> TXT10 C<5:0> Current memory COLUMN value. Note: Valid range TXT mode 0 to 39, CC mode 0 to 47 D<7> D<6> D<5> D<4> D<3> D<2> D<1> D<0> 00H TXT11 D<7:0> TXT12 Data value written or read from memory location defined by TXT9, TXT10 and TXT15 625/525 SYNC ROM VER<4> ROM VER<3> ROM VER<2> ROM VER<1> ROM VER<0> 1 VIDEO SIGNAL QUALITY xxxxxx1xB 625/525 SYNC 0 - 625 line CVBS signal is being received 1 - 525 line CVBS signal is being received Mask programmable identification for character set Rom Version <4> : 0 - Spanish Flicker Stopper Disabled. 1 - Spanish Flicker Stopper Enabled (Controlled by TXT8 Bit-6). ROM VER<4:0> 1 VIDEO SIGNAL QUALITY TXT13 Reserved 0 - Acquisition can not be synchronised to CVBS input. 1 - Acquisition can be synchronised to CVBS VPS RECEIVED 01 - VPS data 0 - No page clearing active 1 - Software or Power On page clear in progress PAGE CLEARING 525 DISPLAY 525 TEXT 625 TEXT PKT 8/30 FASTEXT 0 xxxxxxx0B VPS RECEIVED PAGE CLEARING Table 3 SFR Bit description 2000 Jun 22 27 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names 525 DISPLAY BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET 0 - 625 Line synchronisation for Display. 1 - 525 Line synchronisation for Display. 0 - 525 Line WST not being received 1 - 525 line WST being received 0 - 625 Line WST not being received 1 - 625 line WST being received 0 - No Packet 8/30/x(625) or Packet 4/30/x(525) data detected 1 - Packet 8/30/x(625) or Packet 4/30/x(525) data detected 0 - No Packet x/27 data detected 1 - Packet x/27 data detected Reserved 0 0 0 DISPLAY BANK PAGE<3> PAGE<2> PAGE<1> PAGE<0> 00H 525 TEXT 625 TEXT PKT 8/30 FASTEXT 0 TXT14 DISPLAY BANK 0 - Select lower bank for Display 1 - Select upper bank for Display Current Display page 0 0 0 MICRO BANK BLOCK<3 > BLOCK<2 > BLOCK<1 > BLOCK<0 > 00H PAGE<3:0> TXT15 MICRO BANK 0 - Select lower bank for Micro 1 - Select upper bank for Micro Current Micro block to be accessed by TXT9, TXT10 and TXT11 0 FORCE ACQ<1> FORCE ACQ<0> FORCE DISP<1> FORCE DISP<0> SCREEN COL2 SCREEN COL1 SCREEN COL0 00H BLOCK<3:0> TXT17 FORCE ACQ<1:0> 00 - Automatic Selection 01 - Force 525 timing, Force 525 Teletext Standard 10 - Force 625 timing, Force 625 Teletext Standard 11 - Force 625 timing, Force 525 Teletext Standard 00 - Automatic Selection 01 - Force Display to 525 mode (9 lines per row) 10 - Force Display to 625 mode (10 lines per row) 11 - Not Valid (default to 625) Defines colour to be displayed instead of TV picture and black background. The bits <2:0> are equivalent to the RGB components 000 - Transparent 001 - CLUT entry 9 010 - CLUT entry 10 011- CLUT entry 11 100 - CLUT entry 12 101 - CLUT entry 13 110- CLUT entry 14 111 - CLUT entry 15 NOT<3> NOT<2> NOT<1> NOT<0> 0 0 BS<1> BS<0> 00H FORCE DISP<1:0> SCREEN COL<2:0> TXT18 NOT<3:0> BS<1:0> National Option table selection, maximum of 32 when used with East/West bit Basic Character set selection Table 3 SFR Bit description 28 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names TXT19 TEN BIT7 TEN BIT6 TC<2> BIT5 TC<1> BIT4 TC<0> BIT3 0 TDA955X/6X/8X PS/N1 series BIT2 0 BIT1 TS<1> BIT0 TS<0> RESET 00H 0 - Disable Twist function 1- Enable Twist character set Language control bits (C12/C13/C14) that has Twisted character set Twist Character set selection DRCS ENABLE OSD PLANES 0 0 OSD LANG ENABLE OSD LAN<2> OSD LAN<1> OSD LAN<0> 00H TC<2:0> TS<1:0> TXT20 DRCS ENABLE 0 - Normal OSD characters used 1 - Re-map column 9 to DRCS (TXT and CC modes), 0 - Character code columns 8 and 9 defined as single plane characters 1- Character code columns 8 and 9 defined as double plane characters OSD PLANES OSD LANG ENABLE OSD LAN<2:0> TXT21 Enable use of OSD LAN<2:0> to define language option for display, instead of C12/C13/C14 Alternative C12/C13/C14 bits for use with OSD menus DISP LINES<1> DISP LINES<0> CHAR SIZE<1> CHAR SIZE<0> Reserved CC ON I2C PORT0 CC/TXT 02H DISP LINES<1:0> The number of display lines per character row. 00 - 10 lines per character (defaults to 9 lines in 525 mode) 01 - 13 lines per character 10 - 16 lines per character 11 - reserved Character matrix size. 00 - 10 lines per character (matrix 12x10) 01 - 13 lines per character (matrix 12x13) 10 - 16lines per character (matrix 12x16) 11 - reserved 0 - Closed Caption acquisition off 1 - Closed Caption acquisition on 0 - Disable I2C PORT0 1 - Enable I2C PORT0 selection (P1.7/SDA0, P1.6/SCL0) 0 - Display configured for TXT mode 1 - Display configured for CC mode GPF<7> GPF<6> GPF<5> GPF<4> GPF<3> GPF<2> GPF<1> GPF<0> XXH CHAR SIZE<1:0> CCON I2C PORT0 CC/TXT TXT22 GPF<7:6> GPF<5> General purpose register, bits defined by mask programmable bits 0 - Standard Painter device 1 - Enhanced Painter device 0 - Choose 6 page teletext device 1 - Choose 10 page teletext device 0 - PWM0, PWM1, PWM2 & PWM3 output on Port 3.0 to Port 3.3 respectively 1 - PWM0, PWM1, PWM2 & PWM3 output on Port 2.1 to Port 2.4 respectively GPF<4> (Used for software only) GPF<3> Table 3 SFR Bit description 2000 Jun 22 29 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Names GPF<2> BIT7 BIT6 BIT5 BIT4 BIT3 TDA955X/6X/8X PS/N1 series BIT2 BIT1 BIT0 RESET 0 - Disable Closed Caption acquisition 1 - Enable Closed Caption acquisition 0 - Disable Text acquisition 1 - Enable Text acquisition 0 - Standalone (Painter1_Plus) mode 1 - UOC mode GPF<1> GPF<0> (Polarity reversed in Painter1_Plus standalone) WDT WDv<7:0> WDTKEY WKEY<7:0> WDV<7> WDV<6> WDV<5> WDV<4> WDV<3> WDV<2> WDV<1> WDV<0> 00H Watch Dog Timer period WKEY<7> WKEY<6> WKEY<5> WKEY<4> WKEY<3> WKEY<2> WKEY<1> WKEY<0> 00H Watch Dog Timer Key. Note: Must be set to 55H to disable Watch dog timer when active. 0 0 0 WSS<3:0> ERROR WSS<3> WSS<2> WSS<1> WSS<0> 00H WSS1 WSS<3:0> ERROR WSS<3:0> WSS2 0 - No error in WSS<3:0> 1 - Error in WSS<3:0> Signalling bits to define aspect ratio (group 1) 0 0 0 WSS<7:4> ERROR WSS<7> WSS<6> WSS<5> WSS<4> 00H WSS<7:4> ERROR WSS<7:4> WSS3 0 - No errors in WSS<7:4> 1 - Error in WSS<7:4> Signalling bits to define enhanced services (group 2) WSS<13:11 < ERROR WSS<13> WSS<12> WSS<11> WSS<10:8> ERROR WSS<10> WSS<9> WSS<8> 00H WSS<13:11> ERROR WSS<13:11> WSS<10:8> ERROR WSS<10:8> XRAMP XRAMP<7:0> 0 - No error in WSS<13:11> 1 - Error in WSS<13:11> Signalling bits to define reserved elements (group 4) 0 - No error in WSS<10:8> 1 - Error in WS<10:8> Signalling bits to define subtitles (group 3) XRAMP<7> XRAMP<6> XRAMP<5> XRAMP<4> XRAMP<3> XRAMP<2> XRAMP<1> XRAMP<0> 00H Internal RAM access upper byte address. Table 3 SFR Bit description 2000 Jun 22 30 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller External (Auxiliary + Display) Memory The normal 80C51 external memory area has been mapped internally to the device, this means that the MOVX instruction accesses data memory internal to the device. The movx memory map is shown in Fig.8. TDA955X/6X/8X PS/N1 series consecutive bytes. XRAMP only works on internal MOVX memory. FFH (XRAMP)=FFH 00H FFH (XRAMP)=FEH FF00H FEFFH FFFFH 7FFFH FFFFH MOVX @Ri, A MOVX A, @Ri 00H FE00H MOVX @DPTR,A MOVX A,@DPTR FFH 01FFH (XRAMP)=01H 4800H 47FFH 00H FFH 0100H 00FFH (XRAMP)=00H 8C00H 8BFFH Dynamically Re-definable Characters 8800H 87FFH Display Registers 87F0H 871FH 0200H 01FFH Data RAM(1) 0000H Lower 32K bytes CLUT 8700H 845FH Display RAM for Closed Caption(3) 8000H Upper 32K bytes 00H 0000H Display RAM for TEXT PAGES(2) Fig.9 Indirect addressing (Movx address space) Power-on Reset Power on reset is generated internally to the TDA955x/6x/8x device, hence no external reset circuitry is required. The TV processor die shall generate the master reset in the system, which in turn will reset the microcontroller die A external reset pin is still present and is logically ORed with the internal Power on reset. This pin will only be used for test modes and OTP/ISP programming. The active high reset pin incorporates an internal pull-down, thus it can be left unconnected in application. Power Saving modes of Operation There are three Power Saving modes, Idle, Stand-by and Power Down, incorporated into the Painter1_Plus die. When utilizing either mode, the 3.3v power to the device (Vddp, Vddc & Vdda) should be maintained, since Power Saving is achieved by clock gating on a section by section basis. STAND-BY MODE During Stand-by mode, the Acquisition and Display sections of the device are disabled. The following functions remain active:* 80c51 CPU Core * Memory Interface * I2C * Timer/Counters * WatchDog Timer * SAD and PWMs (1) Amount of Data RAM depends on device, PainterOSD 64K has 0.75K, Painter1.1 has 1K and Painter1.10 has 2K (2) Amount of Display RAM depends on the device, PainterOSD 64K has 1.25K, Painter1.1 has 2K and Painter1.10 has 10K (3) Display RAM for Closed Caption and Text is shared Fig.8 Movx Address Map Auxiliary RAM Page Selection The Auxiliary RAM page pointer is used to select one of the 256 pages within the auxiliary RAM, not all pages are allocated, refer to Fig.9. A page consists of 256 2000 Jun 22 31 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller To enter Stand-by mode, the STAND-BY bit in the ROMBANK register must be set. Once in Stand-By, the XTAL oscillator continues to run, but the internal clock to Acquisition and Display are gated out. However, the clocks to the 80c51 CPU Core, Memory Interface, I2C, Timer/Counters, WatchDog Timer and Pulse Width Modulators are maintained. Since the output values on RGB and VDS are maintained the display output must be disabled before entering this mode. This mode may be used in conjunction with both Idle and Power-Down modes. Hence, prior to entering either Idle or Power-Down, the STAND-BY bit may be set, thus allowing wake-up of the 80c51 CPU core without fully waking the entire device (This enables detection of a Remote Control source in a power saving mode). IDLE MODE During Idle mode, Acquisition, Display and the CPU sections of the device are disabled. The following functions remain active:* Memory Interface * I2C * Timer/Counters * WatchDog Timer * SAD & PWMs To enter Idle mode the IDL bit in the PCON register must be set. The WatchDog timer must be disabled prior to entering Idle to prevent the device being reset. Once in Idle mode, the XTAL oscillator continues to run, but the internal clock to the CPU, Acquisition and Display are gated out. However, the clocks to the Memory Interface, I2C, Timer/Counters, WatchDog Timer and Pulse Width Modulators are maintained. The CPU state is frozen along with the status of all SFRs, internal RAM contents are maintained, as are the device output pin values. Since the output values on RGB and VDS are maintained the Display output must be disabled before entering this mode. There are three methods available to recover from Idle:* Assertion of an enabled interrupt will cause the IDL bit to be cleared by hardware, thus terminating Idle mode. The interrupt is serviced, and following the instruction RETI, the next instruction to be executed will be the one after the instruction that put the device into Idle mode. * A second method of exiting Idle is via an Interrupt generated by the SAD DC Compare circuit. When Painter is configured in this mode, detection of an analogue threshold at the input to the SAD may be used to trigger wake-up of the device i.e. TV Front Panel Key-press. As above, the interrupt is serviced, and following the instruction RETI, the next instruction to be 2000 Jun 22 32 TDA955X/6X/8X PS/N1 series executed will be the one following the instruction that put the device into Idle. * The third method of terminating Idle mode is with an external hardware reset. Since the oscillator is running, the hardware reset need only be active for two machine cycles (24 clocks at 12MHz) to complete the reset operation. Reset defines all SFRs and Display memory to a pre-defined state, but maintains all other RAM values. Code execution commences with the Program Counter set to '0000'. POWER DOWN MODE In Power Down mode the XTAL oscillator still runs, and differential clock transmitter is active. The contents of all SFRs and Data memory are maintained, however, the contents of the Auxiliary/Display memory are lost. The port pins maintain the values defined by their associated SFRs. Since the output values on RGB and VDS are maintained the Display output must be made inactive before entering Power Down mode. The power down mode is activated by setting the PD bit in the PCON register. It is advised to disable the WatchDog timer prior to entering Power down. Recovery from Power-Down takes several milli-seconds as the oscillator must be given time to stabilise. There are three methods of exiting power down:* An External interrupt provides the first mechanism for waking from Power-Down. Since the clock is stopped, external interrupts needs to be set level sensitive prior to entering Power-Down. The interrupt is serviced, and following the instruction RETI, the next instruction to be executed will be the one after the instruction that put the device into Power-Down mode. * A second method of exiting Power-Down is via an Interrupt generated by the SAD DC Compare circuit. When Painter is configured in this mode, detection of a certain analogue threshold at the input to the SAD may be used to trigger wake-up of the device i.e. TV Front Panel Key-press. As above, the interrupt is serviced, and following the instruction RETI, the next instruction to be executed will be the one following the instruction that put the device into Power-Down. * The third method of terminating the Power-Down mode is with an external hardware reset. Reset defines all SFRs and Display memory, but maintains all other RAM values. Code execution commences with the Program Counter set to '0000'. Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller I/O Facility I/O PORTS The IC has 13 I/O lines, each is individually addressable, or form part of 4 parallel addressable ports which are port0, port1, port2 and port3. PORT TYPE All individual ports can be programmed to function in one of four modes, the mode is defined by two Port Configuration SFRs. The modes available are Open Drain, Quasi-bidirectional, High Impedance and Push-Pull. TDA955X/6X/8X PS/N1 series Open Drain The Open drain mode can be used for bi-directional operation of a port. It requires an external pull-up resistor, the pull-up voltage has a maximum value of 5.5V, to allow connection of the device into a 5V environment. Quasi bi-directional The quasi-bidirectional mode is a combination of open drain and push pull. It requires an external pull-up resistor to VDDp (nominally 3.3V). When a signal transition from 0->1 is output from the device, the pad is put into push-pull mode for one clock cycle (166ns) after which the pad goes into open drain mode. This mode is used to speed up the edges of signal transitions. This is the default mode of operation of the pads after reset. High Impedance The high impedance mode can be used for Input only operation of the port. When using this configuration the two output transistors are turned off. Push-Pull The push pull mode can be used for output only. In this mode the signal is driven to either 0V or VDDp, which is nominally 3.3V. Interrupt System The device has 8 interrupt sources, each of which can be enabled or disabled. When enabled, each interrupt can be assigned one of two priority levels. There are four interrupts that are common to the 80C51, two of these are external interrupts (EX0 and EX1) and the other two are timer interrupts (ET0 and ET1). There is also one interrupt connected to the 80c51 micro-controller IIC peripheral for Transmit and Receive operation. The TDA955x/6x/8x family of devices have an additional 16-bit Timer (with 8-bit Pre-scaler). To accommodate this, another interrupt ET2PR has been added to indicate timer overflow. In addition to the conventional 80c51, two application specific interrupts are incorporated internal to the device which have the following functionality:CC (Closed Caption Data Ready Interrupt) - This interrupt is generated when the device is configured for Closed Caption acquisition. The interrupt is activated at the end of the currently selected Slice Line as defined in the CCLIN SFR. BUSY (Display Busy Interrupt) - An interrupt is generated when the Display enters either a Horizontal or Vertical Blanking Period. i.e. Indicates when the micro-controller can update the Display RAM without causing undesired effects on the screen. This interrupt can be configured in one of two modes using the MMR Configuration Register (Address 87FF, Bit-3 [TXT/V]):* TeXT Display Busy: An interrupt is generated on each active horizontal display line when the Horizontal Blanking Period is entered. * Vertical Display Busy: An interrupt is generated on each vertical display field when the Vertical Blanking Period is entered. INTERRUPT ENABLE STRUCTURE Each of the individual interrupts can be enabled or disabled by setting or clearing the relevant bit in the interrupt enable SFRs (IE and IEN1). All interrupt sources can also be globally disabled by clearing the EA bit (IE.7). H1 EX0 ET0 EX1 ET1 ECC ES2 EBUSY IE.0:6 ET2PR IE1.0 Source Enable IE.7 Global Enable IP1.0 Priority Control IP.0:6 H8 L8 Interrupt Source L1 H2 L2 H3 L3 H4 L4 H5 L5 H6 L6 H7 L7 Highest Priority Level1 Highest Priority Level0 Lowest Priority Level1 Lowest Priority Level0 Fig.10 Interrupt Structure INTERRUPT ENABLE PRIORITY Each interrupt source can be assigned one of two priority levels. The interrupt priorities are defined by the interrupt priority SFRs (IP and IP1). A low priority interrupt can be interrupted by a high priority interrupt, but not by another low priority interrupt. A high priority interrupt can not be interrupted by any other interrupt source. If two requests of 33 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller different priority level are received simultaneously, the request with the highest priority level is serviced. If requests of the same priority level are received simultaneously, an internal polling sequence determines which request is serviced. Thus, within each priority level there is a second priority structure determined by the polling sequence as defined in Table 4. Source EX0 ET0 EX1 ET1 ECC ES2 EBUSY ET2PR Lowest Priority within level Highest Interrupt Vector 0003H 000BH 0013H 001BH 0023H 002BH 0033H 003BH TDA955X/6X/8X PS/N1 series In Counter mode, the register is incremented in response to a negative transition at its corresponding external pin T0/1. Since the pins T0/1 are sampled once per machine cycle it takes two machine cycles to recognise a transition, this gives a maximum count rate of 1/24 Fosc = 0.5MHz. There are six special function registers used to control the timers/counters as defined in Table 6. SFR TCON TMOD TL0 TH0 TL1 TH1 Address 88H 89H 8AH 8BH 8CH 8DH Table 6 Timer/Counter Registers Table 4 Interrupt Priority (within same level) TF1 TR TF0 TR IE1 IT1 IE0 IT0 Symbol TF1 Position TCON.7 Name and Significance Timer 1 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine. Timer 1 Run control bit. Set/cleared by software to turn timer.counter on/off. Timer 0 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine. Timer 0 Run control bit. Set/cleared by software to turn timer.counter on/off. Name and Significance Interrupt 1 Edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed. Interrupt 1 Type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts. Interrupt 0 Edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed. Interrupt 0 Type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts. INTERRUPT VECTOR ADDRESS The processor acknowledges an interrupt request by executing a hardware generated LCALL to the appropriate servicing routine. The interrupt vector addresseses are shown in Table 4. LEVEL/EDGE INTERRUPT The external interrupt can be programmed to be either level-activated or transition activated by setting or clearing the IT0/1 bits in the Timer Control SFR(TCON). ITx 0 1 Level Active low INT0 = Negative Edge INT1 = Positive and Negative Edge Edge TR1 TF0 TCON.6 TCON.5 TR0 TCON.4 Symbol IE1 Position TCON.3 IT1 TCON.2 IE0 TCON.1 Table 5 External Interrupt Activation IT0 TCON.0 The external interrupt INT1 differs from the standard 80C51 in that it is activated on both edges when in edge sensitive mode. This is to allow software pulse width measurement for handling remote control inputs. Timer/Counter Two 16 bit timers/counters are incorporated Timer0 and Timer1. Both can be configured to operate as either timers or event counters. In Timer mode, the register is incremented on every machine cycle. It is therefore counting machine cycles. Since the machine cycle consists of 12 oscillator periods, the count rate is 1/12 Fosc = 1MHz. Fig.11 Timer/Counter Control (TCON) register 2000 Jun 22 34 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series Gat C/T M1 M0 Gat C/T M1 M0 Timer 1 Gate Timer 0 C/T Gating control when set. Timer/counter is enabled only while px_int_n is high and TR control bit is set. When cleared timer/counter is enabled whenever TR control bit is set. Timer or Counter selector. Cleared for timer operation (input from system clock). Set for counter operation (input from T input pin. M0 0 1 0 1 Operating 8048 Timer, TL serves as 5-bit prescaler. 16-bit Timer/Counter, TL and TH are cascaded. 8-bit auto-reload Timer/Counter, TH holds a value which is to be loaded into TL. timer 0: two 8-bit Timers/Counters. TL0 is controlled by timer 0 control bits. TH0 is controlled by timer 1 control bits. timer 1: stopped. interrupt. Upon overflow an interrupt should also be generated. Reset values of all registers should be 00 hex. In Timer mode, Timer 2 should count down from the value set on SFRs TP2PR, TP2H and TP2L. It is therefore counting machine cycles. Since the machine cycle consists of 12 oscillator periods, the count rate is 1/12 fosc (1MHz). Timer2 interval = ( TP2H * 256 + TP2L ) * ( TP2PR + 1 ) * 1 us M1 0 0 1 1 Fig.12 Timer/Counter Mode control (TMOD) The Timer/Counter function is selected by control bits C/T in the Timer Mode SFR (TMOD). These two Timer/Counter have four operating modes, which are selected by bit-pairs (M1.M0) in the TMOD. Refer to the 80C51 based 8-bit micro-controllers - Philips Semiconductors (ref. IC20) for detail of the modes and operation. TL0/TL1 and TH0/TH1 are the actual timer/counter registers for timer0 / timer1. TL0/TL1 is the low byte and TH0/TH1 is the high byte. TIMER WITH PRE-SCALER An additional 16-bit timer with 8-bit pre-scaler is provided to allow timer periods up to 16.777 seconds. This timer remains active during IDLE mode. TP2L sets the lower value of the period for timer 2 and TP2H is the upper timer value. TP2PR provides an 8-bit pre-scaler for timer 2. The value on TP2PR, TP2H and TP2L shall never change unless updated by the software. If the micro reads TP2R, TP2H orTP2L at any stage, this should return the value written and not the current timer 2 value. The timer 2 should continue after overflow by re-loading the timer with the values of SFRs TP2PR, TP2H and TP2L. TP2CL and TP2CH indicate the current timer 2 value. These should be readable both when the timer 2 is active and inactive. Once the timer 2 is disabled, the timer 2 value at the time of disabling should be maintained on the SFRs TP2CL and TP2CH. At a count of zero (on TP2CL and TP2CH), the overflow flag should be set :- TP2CRL<1> '0' = no timer 2 overflow, '1'= timer 2 overflow. TP2CRL is the control and status for timer 2. TP2CRL.0 is the timer enable and TP2CRL.1 is the timer overflow status. The overflow flag will need to be reset by software. Hence, if required, software may poll flag rather than use 2000 Jun 22 35 WatchDog Timer The WatchDog timer is a counter that once in an overflow state forces the micro-controller in to a reset condition. The purpose of the WatchDog timer is to reset the micro-controller if it enters an erroneous processor state (possibly caused by electrical noise or RFI) within a reasonable period of time. When enabled, the WatchDog circuitry will generate a system reset if the user program fails to reload the WatchDog timer within a specified length of time known as the WatchDog interval. The WatchDog timer consists of an 8-bit counter with an 16-bit pre-scaler. The pre-scaler is fed with a signal whose frequency is 1/12 fosc (1MHz). The 8 bit timer is incremented every `t' seconds where: t=12x65536x1/fosc=12x65536x1/12x106 = 65.536ms WATCHDOG TIMER OPERATION The WatchDog operation is activated when the WLE bit in the Power Control SFR (PCON) is set. The WatchDog can be disabled by Software by loading the value 55H into the WatchDog Key SFR (WDTKEY). This must be performed before entering Idle/Power Down mode to prevent exiting the mode prematurely. Once activated the WatchDog timer SFR (WDT) must be reloaded before the timer overflows. The WLE bit must be set to enable loading of the WDT SFR, once loaded the WLE bit is reset by hardware, this is to prevent erroneous Software from loading the WDT SFR. The value loaded into the WDT defines the WatchDog interval. WatchDog interval = (256 - WDT) * t = (256 -WDT) * 65.536ms. The range of intervals is from WDT=00H which gives 16.777s to WDT=FFH which gives 65.536ms. PORT Alternate Functions The Ports 1,2 and 3 are shared with alternate functions to enable control of external devices and circuitry. The alternate functions are enabled by setting the appropriate Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller SFR and also writing a `1' to the Port bit that the function occupies. PWM PULSE WIDTH MODULATORS The device has four 6-bit Pulse Width Modulated (PWM) outputs for analogue control of e.g. volume, balance, bass, treble, brightness, contrast, hue and saturation. The PWM outputs generate pulse patterns with a repetition rate of 21.33us, with the high time equal to the PWM SFR value multiplied by 0.33us. The analogue value is determined by the ratio of the high time to the repetition time, a D.C. voltage proportional to the PWM setting is obtained by means of an external integration network (low pass filter). TDA955X/6X/8X PS/N1 series instruction cycle after the SAD<7:0> value has been set. The result of the comparison is given on VHI one instruction cycle after the setting of ST. VDDP ADC0 ADC1 MUX ADC2 ADC3 CH<1:0> 4-1 VHI + 8-bit DAC PWM Control The relevant PWM is enabled by setting the PWM enable bit PWxE in the PWMx Control register. The high time is defined by the value PWxV<5:0> TPWM TUNING PULSE WIDTH MODULATOR The device has a single 14-bit PWM that can be used for Voltage Synthesis Tuning. The method of operation is similar to the normal PWM except the repetition period is 42.66us. SAD<7:0> Fig.13 SAD Block Diagram TPWM Control Two SFRs are used to control the TPWM, they are TDACL and TDACH. The TPWM is enabled by setting the TPWE bit in the TDACH SFR. The most significant bits TD<13:7> alter the high period between 0 and 42.33us. The 7 least significant bits TD<6:0> extend certain pulses by a further 0.33us. e.g. if TD<6:0> = 01H then 1 in 128 periods will be extended by 0.33us, if TD<6:0>=02H then 2 in 128 periods will be extended. The TPWM will not start to output a new value until TDACH has been written to. Therefore, if the value is to be changed, TACL should be written before TDACH. SAD SOFTWARE A/D Four successive approximation Analogue to Digital Converters can be implemented in software by making use of the on board 8-bit Digital to Analogue Converter and Analogue Comparator. SAD Input Voltage The external analogue voltage that is used for comparison with the internally generated DAC voltage does not have the same voltage range. The DAC has a lower reference level of VSSA and an upper reference level of VSSA. The resolution of the DAC voltage with a nominal value is 3.3/256 ~ 13mV. The external analogue voltage has a lower value equivalent to VSSA and an upper value equivalent to VDDP - Vtn, were Vtn is the threshold voltage for an NMOS transistor. The reason for this is that the input pins for the analogue signals (P3.0 to P3.3) are 5V tolerant for normal port operations, i.e. when not used as analogue input. To protect the analogue multiplexer and comparator circuitry from the 5V, a series transistor is used to limit the voltage. This limiting introduces a voltage drop equivalent to Vtn (~0.6V) on the input voltage. Therefore, for an input voltage in the range VDDP to VDDp-Vtn the SAD returns the same comparison value. SAD DC Comparator Mode The SAD module incorporates a DC Comparator mode which is selected using the 'DC_COMP' control bit in the SADB SFR. This mode enables the micro-controller to detect a threshold crossing at the input to the selected analogue input pin (P3.0, P3.1, P3.2 or P3.3) of the Software A/D Converter. A level sensitive interrupt is generated when the analogue input voltage level at the pin falls below the analogue output level of the SAD D/A converter. This mode is intended to provide the device with a wake-up mechanism from Power-Down or Idle when a key-press on the front panel of the TV is detected. SAD Control The control of the required analogue input is done using the channel select bits CH<1:0> in the SAD SFR, this selects the required analogue input to be passed to one of the inputs of the comparator. The second comparator input is generated by the DAC whose value is set by the bits SAD<7:0> in the SAD and SADB SFRs. A comparison between the two inputs is made when the start compare bit ST in the SAD SFR is set, this must be at least one 2000 Jun 22 36 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller The following software sequence should be used when utilizing this mode for Power-Down or Idle:1. Disable INT1 using the IE SFR. 2. Set INT1 to level sensitive using the TCON SFR. 3. Set the D/A Converter digital input level to the desired threshold level using the SAD/SADB SFRs and select the required input pin (P3.0, P3.1, P3.2 or P3,3) using CH1, CH0 in the SAD SFR. 4. Enter DC Compare mode by setting the 'DC_COMP' enable bit in the SADB SFR. 5. Enable INT1 using the IE SFR. 6. Enter Power-Down/Idle. Upon wake-up the SAD should be restored to its conventional operating mode by disabling the 'DC_COMP' control bit. I2C Serial I/O Bus The I2C bus consists of a serial data line (SDA) and a serial clock line (SCL). The definition of the I2C protocol can be found in the 80C51 based 8-bit micro-controllers - Philips Semiconductors (ref. IC20). The device operates in four modes: * Master Transmitter * Master Receiver * Slave Transmitter * Slave Receiver The micro-controller peripheral is controlled by the Serial Control SFR (S1CON) and its Status is indicated by the status SFR (S1STA). Information is transmitted/received to/from the I2C bus using the Data SFR (S1DAT) and the Slave Address SFR (S1ADR) is used to configure the slave address of the peripheral. The byte level I2C serial port is identical to the I2C serial port on the 8xC558, except for the clock rate selection bits CR<2:0>. The operation of the subsystem is described in detail in the 8xC558 datasheet and can be found in the 80C51 based 8-bit micro-controllers - Philips Semiconductors (ref. IC20). Three different IIC selection tables for CR<2:0> can be configured using the ROMBANK SFR (IIC_LUT<1:0>) as follows: CR2 0 0 0 0 1 1 1 1 TDA955X/6X/8X PS/N1 series `558 nominal mode' (iic_lut="00") This option accommodates the 558 I2C. The various serial rates are shown below: - fclk (6MHz) CR2 0 0 0 0 1 1 1 1 CR1 0 0 1 1 0 0 1 1 CR0 0 1 0 1 0 1 0 1 divided by 60 1600 40 30 240 3200 160 120 I2C Bit Frequency (KHz) at fclk 100 3.75 150 200 25 1.875 37.5 50 Table 7 IIC Serial Rates `558 nominal mode' `558 fast mode' (iic_lut="01") This option accommodates the 558 I2C doubled rates as shown below: - fclk (6MHz) CR1 0 0 1 1 0 0 1 1 CR0 0 1 0 1 0 1 0 1 divided by 30 800 20 15 120 1600 80 60 I2C Bit Frequency (KHz) at fclk 200 7.5 300 400 50 3.75 75 100 Table 8 IIC Serial Rates `558 fast mode' `558 slow mode' (iic_lut="10") This option accommodates the 558 I2C rates divided by 2 as shown below: - fclk (6MHz) CR2 0 0 0 0 1 1 CR1 0 0 1 1 0 0 CR0 0 1 0 1 0 1 divided by 120 3200 80 60 480 6400 I2C Bit Frequency (KHz) at fclk 50 1.875 75 100 12.5 0.9375 Table 9 IIC Serial Rates `558 slow mode' 2000 Jun 22 37 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller fclk (6MHz) CR2 1 1 CR1 1 1 CR0 0 1 divided by 320 240 TDA955X/6X/8X PS/N1 series I2C Bit Frequency (KHz) at fclk 18.75 25 Data Capture Features * Video Signal Quality detector. * Data Capture for 625 line WST * Data Capture for 525 line WST * Data Capture for US Closed Caption * Data Capture for VPS data (PDC system A) * Data Capture for Wide Screen Signalling (WSS) bit decoding * Automatic selection between 525 WST/625WST * Automatic selection between 625WST/VPS on line 16 of VBI * Real-time capture and decoding for WST Teletext in Hardware, to enable optimised microprocessor throughput * Upto 10 pages stored On-Chip * Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) * Automatic detection of FASTEXT transmission * Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters * Signal quality detector for WST/VPS data types * Comprehensive Teletext language coverage * Full Field and Vertical Blanking Interval (VBI) data capture of WST data Analogue to Digital Converter The CVBS input is passed through a differential to single ended converter (DIVIS), although in this device it is used in single ended configuration with a reference.The analogue output of DIVIS is converted into a digital representation by a full flash ADC with a sampling rate of 12MHz. Multi Rate Video Input Processor The multi rate video input processor is a Digital Signal Processor designed to extract the data and recover the clock from the digital CVBS signal. Table 9 IIC Serial Rates `558 slow mode' Note: In the above tables the fclk relates to the clock rate of the 80c51 IIC module (6MHz). I2C Port Enable One external I2C port is available. This port is enabled using TXT21.I2C PORT0. Any information transmitted to the device can only be acted upon if the port is enabled. Internal communication between the 80c51 micro-controller and the TV Signal Processor will continue regardless of the value written to TXT21.I2C PORT0. LED Support Port pins P0.5 and P0.6 have a 8mA current sinking capability to enable LEDs in series with current limiting resistors to be driven directly, without the need for additional buffering circuitry. MEMORY INTERFACE The memory interface controls the access to the embedded DRAM, refreshing of the DRAM and page clearing. The DRAM is shared between Data Capture, Display and Microcontroller sections. The Data Capture section uses the DRAM to store acquired information that has been requested. The Display reads the DRAM information and converts it to RGB output values. The Microcontroller uses the DRAM as embedded auxiliary RAM. DATA CAPTURE The Data Capture section takes in the analogue Composite Video and Blanking Signal (CVBS) from One Chip, and from this extracts the required data, which is then decoded and stored in SFR memory. The extraction of the data is performed in the digital domain. The first stage is to convert the analogue CVBS signal into a digital form. This is done using an ADC sampling at 12MHz. The data and clock recovery is then performed by a Multi-Rate Video Input Processor (MulVIP). From the recovered data and clock the following data types are extracted WST Teletext (625/525),Closed Caption, VPS, WSS. The extracted data is stored in either memory (DRAM) via the Memory Interface or in SFR locations. 2000 Jun 22 38 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Data Standards The data and clock standards that can be recovered are shown in Table 10 below:Data Standard 625WST 525WST VPS WSS Closed Caption Clock Rate 6.9375 MHz 5.7272 MHz 5.0 MHz 5.0 MHz 500 KHz TDA955X/6X/8X PS/N1 series than 09h, then data being written to TXT3 is ignored. Table 11 shows the contents of the page request RAM. Up to 10 pages of teletext can be acquired on the 10 page device, when TXT1.EXT PKT OFF is set to logic 1, and up to 9 pages can be acquired when this bit is set to logic 0. f the 'Do Care' bit for part of the page number is set to 0 then that part of the page number is ignored when the teletext decoder is deciding whether a page being received off air should be stored or not. For example, if the Do Care bits for the 4 subcode digits are all set to 0 then every subcode version of the page will be captured. Start Column 0 Byte Identification Magazine Page Tens Page Units Hours Tens Hours Units Minutes Tens Minutes Units Error Mode PRD<4> DO CARE DO CARE DO CARE DO CARE DO CARE DO CARE DO CARE x PRD<3> HOLD PT3 PU3 x HU3 x MU3 x PRD<2> MAG2 PT2 PU2 x HU2 MT2 MU2 x PRD<1> MAG1 PT1 PU1 HT1 HU1 MT1 MU1 E1 PRD<0> MAG0 PT0 PU0 HT0 HU0 MT0 MU0 E0 Table 10 Data Slicing Standards Data Capture Timing The Data Capture timing section uses the Synchronisation information extracted from the CVBS signal to generate the required Horizontal and Vertical reference timings. The timing section automatically recognises and selects the appropriate timings for either 625 (50Hz) synchronisation or 525 (60Hz) synchronisation. A flag TXT12.Video Signal Quality is set when the timing section is locked correctly to the incoming CVBS signal. When TXT12.Video Signal Quality is set another flag TXT12.625/525 SYNC can be used to identify the standard. Acquisition The acquisition sections extracts the relevant information from the serial stream of data from the MulVIP and stores it in memory. 625 WST ACQUISITION The family is capable of acquiring 625-line and 525-line World System Teletext. Teletext pages are identified by seven numbers: magazine (page hundreds), page tens, page units, hours tens, hours units, minutes tens and minutes units. The last four digits, hours and minutes, are known as the subcode, and were originally intended to be time related, hence their names. 1 2 3 4 5 6 7 Table 11 The contents of the Page request RAM Note: MAG = Magazine PT = Page Tens PU = Page Units HT = Hours Tens HU = Hours Units MT = Minutes Tens MU = Minutes Units E = Error check mode When the Hold bit is set to 0 the teletext decoder will not recognise any page as having the correct page number and no pages will be captured. In addition to providing the user requested hold function this bit should be used to prevent the inadvertent capture of an unwanted page when a new page request is being made. For example, if the previous page request was for page 100 and this was being changed to page 234, it would be possible to capture page 200 if this arrived after only the requested magazine number had been changed. The E1 and E0 bits control the error checking which should be carried out on packets 1 to 23 when the page being requested is captured. This is described in more detail in a later section (`Error Checking'). For a multi page device, each packet can only be written into one place in the teletext RAM so if a page matches more than one of the page requests the data is written into the area of memory corresponding to the lowest numbered matching page request. At power-up each page request defaults to any page, hold on and error check mode 0. Making a page request A page is requested by writing a series of bytes into the TXT3.PRD<4:0> SFR which correspond to the number of the page required. The bytes written into TXT3 are stored in a RAM with an auto-incrementing address. The start address for the RAM is set using the TXT2.SC<2:0> to define which part of the page request is being written, and TXT2.REQ<3:0> is used to define which of the 10 page requests is being modified. If TXT2.REQ<3:0> is greater Rolling Headers and Time When a new page has been requested it is conventional for the decoder to turn the header row of the display green 2000 Jun 22 39 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller and to display each page header as it arrives until the correct page has been found. When a page request is changed (i.e.: when the TXT3 SFR is written to) a flag (PBLF) is written into bit 5, column 9, row 25 of the corresponding block of the page memory. The state of the flag for each block is updated every TV line, if it is set for the current display block, the acquisition section writes all valid page headers which arrive into the display block and automatically writes an alpha-numerics green character into column 7 of row 0 of the display block every TV line. When a requested page header is acquired for the first time, rows 1 to 23 of the relevant memory block are cleared to space, i.e.: have 20h written into every column, before the rest of the page arrives. Row 24 is also cleared if the TXT0.X24 POSN bit is set. If the TXT1.EXT PKT OFF bit is set the extension packets corresponding to the page are also cleared. The last 8 characters of the page header are used to provide a time display and are always extracted from every valid page header as it arrives and written into the display block The TXT0. DISABLE HEADER ROLL bit prevents any data being written into row 0 of the page memory except when a page is acquired off air i.e.: rolling headers and time are not written into the memory. The TXT1.ACQ OFF bit prevents any data being written into the memory by the teletext acquisition section. When a parallel magazine mode transmission is being received only headers in the magazine of the page requested are considered valid for the purposes of rolling headers and time. Only one magazine is used even if don't care magazine is requested. When a serial magazine mode transmission is being received all page headers are considered to be valid. TDA955X/6X/8X PS/N1 series each of blocks 0 to 8 contains a teletext page arranged in the same way as the basic page memory of the page device and block 9 contains extension packets. When the TXT1.EXT PKT OFF bit is logic 1, no extension packets are captured and block 9 of the memory is used to store another page. The number of the memory block into which a page is written corresponds to the page request number which resulted in the capture of the page. Packet 0, the page header, is split into 2 parts when it is written into the text memory. The first 8 bytes of the header contain control and addressing information. They are Hamming decoded and written into columns 0 to 7 of row 25. Row 25 also contains the magazine number of the acquired page and the PBLF flag but the last 14 bytes are unused and may be used by the software, if necessary. Error Checking Before teletext packets are written into the page memory they are error checked. The error checking carried out depends on the packet number, the byte number, the error check mode bits in the page request data and the TXT1.8 BIT bit. If an incorrectable error occurs in one of the Hamming checked addressing and control bytes in the page header or in the Hamming checked bytes in packet 8/30, bit 4 of the byte written into the memory is set, to act as an error flag to the software. If incorrectable errors are detected in any other Hamming checked data the byte is not written into the memory. Teletext Memory Organisation The teletext memory is divided into 2 banks of 10 blocks. Normally, when the TXT1.EXT PKT OFF bit is logic 0, 2000 Jun 22 40 Row 25 Data Contents The Hamming error flags are set if the on-board 8/4 Hamming checker detects that there has been an incorrectable (2 bit) error in the associated byte. It is possible for the page to still be acquired if some of the page address information contains incorrectable errors if that part of the page request was a 'don't care'. There is no error flag for the magazine number as an incorrectable error in this information prevents the page being acquired. The interrupted sequence (C9) bit is automatically dealt with by the acquisition section so that rolling headers do not contain a discontinuity in the page number sequence. The magazine serial (C11) bit indicates whether the transmission is a serial or a parallel magazine transmission. This affects the way the acquisition section operates and is dealt with automatically. The newsflash (C5), subtitle (C6), suppress header (C7), inhibit display (C10) and language control (C12 to 14) bits are dealt with automatically by the display section, described below. The update (C8) bit has no effect on the hardware. The remaining 32 bytes of the page header are parity checked and written into columns 8 to 39 of row 0. Bytes which pass the parity check have the MSB set to 0 and are written into the page memory. Bytes with parity errors are not written into the memory. Inventory Page If the TXT0.INV on bit is 1, memory block 8 is used as an inventory page. The inventory page consists of two tables, - the Transmitted Page Table (TPT) and the subtitle page table (SPT). In each table, every possible combination of the page tens and units digit, 00 to FFh, is represented by a byte. Each bit of these bytes corresponds to a magazine number so each page number, from 100 to 8FF, is represented by a bit in the table.The bit for a particular page in the TPT is set Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller when a page header is received for that page. The bit in the SPT is set when a page header for the page is received which has the `subtitle' page header control bit (C6) set.The bit for a particular page in the TPT is set when a page header is received for that page. The bit in the SPT is set when a page header for the page is received which has the `subtitle' page header control bit (C6) set. TDA955X/6X/8X PS/N1 series Packet 26 Processing One of the uses of packet 26 is to transmit characters which are not in the basic teletext character set. The family automatically decodes packet 26 data and, if a character corresponding to that being transmitted is available in the character set, automatically writes the appropriate character code into the correct location in the teletext memory. This is not a full implementation of the packet 26 specification allowed for in level 2 teletext, and so is often referred to as level 1.5. By convention, the packets 26 for a page are transmitted before the normal packets. To prevent the default character data over writing the packet 26 data the device incorporates a mechanism which prevents packet 26 data from being overwritten. This mechanism is disabled when the Spanish national option is detected as the Spanish transmission system sends even parity (i.e. incorrect) characters in the basic page locations corresponding to the characters sent via packet 26 and these will not over write the packet 26 characters anyway. The special treatment of Spanish national option is prevented if TXT12. ROM VER R4 is logic 0 or if the TXT8.DISABLE SPANISH is set. Packet 26 data is processed regardless of the TXT1. EXT PKT OFF bit, but setting theTXT1.X26 OFF disables packet 26 processing. The TXT8. Packet 26 received bit is set by the hardware whenever a character is written into the page memory by the packet 26 decoding hardware. The flag can be reset by writing a 0 into the SFR bit. 525 WST The 525 line format is similar to the 625 line format but the data rate is lower and there are less data bytes per packet (32 rather than 40). There are still 40 characters per display row so extra packets are sent each of which contains the last 8 characters for four rows. These packets can be identified by looking at the `tabulation bit' (T), which replaces one of the magazine bits in 525 line teletext. When an ordinary packet with T = 1 is received, the decoder puts the data into the four rows starting with that corresponding to the packet number, but with the 2 LSBs set to 0. For example, a packet 9 with T = 1 (packet X/1/9) contains data for rows 8, 9, 10 and 11. The error checking carried out on data from packets with T = 1 depends on the 2000 Jun 22 41 setting of the TXT1. 8 BIT bit and the error checking control bits in the page request data and is the same as that applied to the data written into the same memory location in the 625 line format. The rolling time display (the last 8 characters in row 0) is taken from any packets X/1/1, 2 or 3 received. In parallel magazine mode only packets in the correct magazine are used for rolling time. Packet number X/1/0 is ignored. The tabulation bit is also used with extension packets. The first 8 data bytes of packet X/1/24 are used to extend the Fastext prompt row to 40 characters. These characters are written into whichever part of the memory the packet 24 is being written into (determined by the `X24 Posn' bit). Packets X/0/27/0 contain 5 Fastext page links and the link control byte and are captured, Hamming checked and stored by in the same way as are packets X/27/0 in 625 line text. Packets X/1/27/0 are not captured. Because there are only 2 magazine bits in 525 line text, packets with the magazine bits all set to 0 are referred to as being in magazine 4. Therefore, the broadcast service data packet is packet 4/30, rather than packet 8/30. As in 625 line text, the first 20 bytes of packet 4/30 contain encoded data which is decoded in the same way as that in packet 8/30. The last 12 bytes of the packet contains half of the parity encoded status message. Packet 4/0/30 contains the first half of the message and packet 4/1/30 contains the second half. The last 4 bytes of the message are not written into memory. The first 20 bytes of the each version of the packet are the same so they are stored whenever either version of the packet is acquired. In 525 line text each packet 26 only contains ten 24/18 Hamming encoded data triplets, rather than the 13 found in 625 line text. The tabulation bit is used as an extra bit (the MSB) of the designation code, allowing 32 packet 26s to be transmitted for each page. The last byte of each packet 26 is ignored. FASTEXT DETECTION When a packet 27, designation code 0 is detected, whether or not it is acquired, the TXT13. FASTEXT bit is set. If the device is receiving 525 line teletext, a packet X/0/27/0 is required to set the flag. The flag can be reset by writing a 0 into the SFR bit. BROADCAST SERVICE DATA DETECTION When a packet 8/30 is detected, or a packet 4/30 when the device is receiving a 525 line transmission, the TXT13. Packet 8/30. The flag can be reset by writing a 0 into the SFR bit. VPS ACQUISITION When the TXT0. VPS ON bit is set, any VPS data present on line 16, field 0 of the CVBS signal at the input of the Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller teletext decoder is error checked and stored in row 25, block 9 of the basic page memory. The device automatically detects whether teletext or VPS is being transmitted on this line and decodes the data appropriately. TDA955X/6X/8X PS/N1 series column 0 Teletext page row 25 header data 9 10 11 12 13 14 15 16 17 18 19 20 21 VPS VPS byte 14 byte 15 VPS byte 4 22 23 VPS byte 5 VPS byte 11 VPS VPS byte 12 byte 13 Fig.14 VPS Data Storage Each VPS byte in the memory consists of 4 bi-phase decoded data bits (bits 0-3), a bi-phase error flag (bit 4) and three 0s (bits5-7). The TXT13. VPS Received bit is set by the hardware whenever VPS data is acquired. The flag can be reset by writing a 0 into the SFR bit. DISPLAY The display section is based on the requirements for a Level 1.5 WST Teletext and US Closed Caption. There are some enhancements for use with locally generated On-Screen Displays. The display section reads the contents of the Display memory and interprets the control/character codes. Using this information and other global settings, the display produces the required RGB signals and Video/Data (Fast Blanking) signal for the TV signal processing. The display is synchronised to the TV signal processing by way of Horizontal and Vertical sync signals generated within TDA955x/6x/8x. From these signals all display timings are derived. Display Features * Teletext and Enhanced OSD modes * Level 1.5 WST features * US Closed Caption Features * Serial and Parallel Display Attributes * Single/Double/Quadruple Width and Height for characters * Scrolling of display region. * Variable flash rate controlled by software. * Globally selectable scan lines per row 9/10/13/16. * Globally selectable character matrix (HxV) 12x9, 12x10, 12x13, 12x16. * Italics, Underline and Overline. * Soft Colours using CLUT with 4096 colour palette. * Fringing (Shadow) selectable from N-S-E-W direction. * Fringe colour selectable. * Meshing of defined area. * Contrast reduction of defined area. * Cursor. * Special Graphics characters with two planes, allowing four colours per character. * 32 Software re-definable On-Screen Display characters. * 4 WST Character sets(G0/G2) in single device (e.g. Latin,Cyrillic,Greek,Arabic). * G1 Mosaic graphics, Limited G3 Line drawing characters. * WST Character sets and Closed Caption Character set in single device. Display Modes The display section has two distinct modes with different features available in each. The two modes are: WSS ACQUISITION The Wide Screen Signalling data transmitted on line 23 gives information on the aspect ratio and display position of the transmitted picture, the position of subtitles and on the camera/film mode. Some additional bits are reserved for future use. A total of 14 data bits are transmitted. All of the available data bits transmitted by the Wide Screen Signalling signal are captured and stored in SFRs WSS1, WSS2 and WSS3. The bits are stored as groups of related bits and an error flag is provided for each group to indicate when a transmission error has been detected in one or more of the bits in the group. Wide screen signalling data is only acquired when the TXT8.WSS ON bit is set. The TXT8.WSS RECEIVED bit is set by the hardware whenever wide screen signalling data is acquired. The flag can be reset by writing a 0 into the SFR bit. CLOSED CAPTION ACQUISITION The US Closed Caption data is transmitted on line 21 (525 line timings) and is used for Captioning information, Text information and Extended Data Services. Closed Caption data is only acquired when TXT21.CC ON bit is set. Two bytes of data are stored per field in SFRs, the first bye is stored in CCDAT1 and the second byte is stored in CCDAT2. The value in the CCDAT registers are reset to 00h at the start of the Closed Caption line defined by CCLIN.CS<4:0>. At the end of the Closed Caption line an interrupt is generated if IE.ECC is active. The processing of the Closed Caption data to convert into a displayable format is performed by Software. 2000 Jun 22 42 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller * TXT:This is the display configured as the WST mode with additional serial and global attributes to enable the same functionality as the SAA5497 (ETT) device.The display is configured as a fixed 25 rows with 40 characters per row. * CC:This is the display configured as the US Closed Caption mode with the same functionality as the PC83C771 device. The display is configured as a maximum of 16 rows with a maximum of 48 characters per row. In both of the above modes the Character matrix, and TV lines per row can be defined. There is an option of 9, 10, 13 & 16 TV lines per display row, and a Character matrix (HxV) of 12x9, 12x10, 12x13, or 12x16. Not all combinations of TV lines per row and maximum display rows give a sensible OSD display, since there is limited number of TV scan lines available. Special Function Register, TXT21 is used to control the character matrix and lines per row. TDA955X/6X/8X PS/N1 series Display Features available in each mode The following is a list of features available in each mode. Each setting can either be a serial or parallel attribute, and some have a global effect on the display. Feature Flash Boxes Horizontal Size Vertical Size TXT serial Txt/OSD (Serial) x1/x2/x4 (serial) x1/x2 (serial) x4 (global) N/A 8 (serial) 8 (serial) 16 from 4096 N/A N/A N+S+E+W 16 (Global) Black or Colour (Global) YES 16 (Global) 32 (Global) 12x9/10/13/16 25 40 1000 YES 16 CC serial serial x1/x2 (serial) x1/x2 (serial) Italic Foreground colours Background colours Soft Colours (CLUT) Underline Overline Fringe Fringe Colour Meshing of Background Fast Blanking Polarity Screen Colour DRCS Character Matrix (HxV) No. of Rows No. of Columns No of Characters displayable Cursor Special Graphics (2 planes per character) Scroll serial 8+8 (parallel) 16 (serial) 16 from 4096 serial serial N+S+E+W 16 (Serial) All (Global) YES 16 (Global) 32 (Global) 12x9/10/13/16 16 48 768 YES 16 NO YES Table 12 Display Features 2000 Jun 22 43 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Display Feature Descriptions FLASH Flashing causes the foreground colour pixel to be displayed as the background pixels.The flash frequency is controlled by software setting and resetting display register REG0: Status at the appropriate interval. CC: This attribute is valid from the time set (see Table 18) until the end of the row or until otherwise modified. TXT: This attribute is set by the control character `flash' (08h) and remains valid until the end of the row or until reset by the control character `steady' (09h). BOXES CC: This attribute is valid from the time set until end of row or otherwise modified if set with Serial Mode 0. If set with Serial Mode 1, then it is set from the next character onwards. In CC text mode the background colour is displayed regardless of the setting of the box attribute bit. Boxes take affect only during mixed mode, where boxes are set in this mode the background colour is displayed. Character locations where boxes are not set show video/screen colour (depending on the setting in the display control register. REG0: Display Control) in stead of the background colour. TXT: Two types of boxes exist the Teletext box and the OSD box. The Teletext box is activated by the `start box' control character (0Bh), Two start box characters are required begin a Teletext box, with box starting between the 2 characters. The box ends at the end of the line or after a `end box' control character. TXT mode can also use OSD boxes, they are started using size implying OSD control chracters(BCh/BDh/BEh/BFh). The box starts after the control character (`set after') and ends either at the end of the row or at the next size implying OSD character (`set at'). The attributes flash, teletext box, conceal, separate graphics, twist and hold graphics are all reset at the start of an OSD box, as they are at the start of the row. OSD Boxes are only valid in TV mode which is defined by TXT5=03h and TXT6=03h. SIZE The size of the characters can be modified in both the horizontal and vertical directions. CC: Two sizes are available in both the horizontal and vertical directions. The sizes available are normal (x1), double (x2) height/width and any combination of these. The attribute setting is always valid for the whole row. Mixing of sizes within a row is not possible. TXT: Three horizontal sizes are available normal(x1),double(x2),quadruple(x4). The control characters `normal size' (0Ch/BCh) enables normal size, 2000 Jun 22 44 TDA955X/6X/8X PS/N1 series the `double width' or double size (0Eh/BEh/0Fh/BFh) enables double width characters. Any two consecutive combination of `double width' or `double size' (0Eh/BEh/0Fh/Bfh) activates quadruple width characters, provided quadruple width characters are enabled by TXT4.Quad Width Enable. Three vertical sizes are available normal(x1),double(x2),quadruple(x4). The control characters `normal size' (0Ch/BCh) enable normal size, the `double height' or `double size' (0Dh/BDh/0Fh/BFh) enable double height characters. Quadruple height character are achieved by using double height characters and setting the global attributes TXT7.Double Height(expand) and TXT7.Bottom/Top. If double height characters are used in teletext mode, single height characters in the lower row of the double height character are automatically disabled. ITALIC CC: This attribute is valid from the time set until the end of the row or otherwise modified. The attribute causes the character foreground pixels to be offset horizontally by 1 pixel per 4 scan lines (interlaced mode). The base is the bottom left character matrix pixel. The pattern of the character is indented as shown in Fig.15. Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TXT: The Italic attribute is not available. TDA955X/6X/8X PS/N1 series 12x16 character matrix 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 12x13 character matrix 12x10 character matrix 0 2 4 6 8 10 0 2 4 6 8 10 0 2 4 6 8 10 0 2 4 6 8 10 0 2 4 6 8 10 0 2 4 6 8 10 Indented by 7/6/4 Indented by 6/5/3 Indented by 5/4/2 Indented by 4/3/1 Indented by 3/2/0 Indented by 2/1 Indented by 1/0 Indented by 0 Field 1 Field 2 Fig.15 Italic Characters (12x10, 12x13 & 12x16). TXT: The foreground colour is selected via a control character. The colour control characters takes effect at the start of the next character ("Set-After") and remain valid until the end of the row, or until modified by a control character. Only 8 foreground colours are available. The TEXT foreground control characters map to the CLUT entries as shown below: COLOURS CLUT (Colour Look Up Table) A CLUT (Colour Look Up Table) with 16 colour entries is provided. The colours are programmable out of a palette of 4096(4 bits per R, G and B). The CLUT is defined by writing data to a RAM that resides in the MOVX address space of the 80C51. RED3-0 b11. . .b4 0000 0000 ... 1111 1111 GRN3-0 b7. . .b4 0000 0000 ... 1111 1111 BLU3-0 b3. . .b0 0000 1111 ... 0000 1111 Colour entry 0 1 ... 14 15 Control Code 00h 01h 02h 03h 04h 05h 06h 07h Defined Colour Black Red Green Yellow Blue Magenta Cyan White CLUT Entry 0 1 2 3 4 5 6 7 Table 13 CLUT Colour values Table 14 Foreground CLUT mapping Foreground Colour CC: The foreground colour can be chosen from 8 colours on a character by character basis. Two sets of 8 colours are provided. A serial attribute switches between the banks (see Table 18 Serial Mode 1, bit 7). The colours are the CLUT entries 0 to 7 or 8 to 15. Background Colour CC: This attribute is valid from the time set until end of row or otherwise modified if set with Serial Mode 0. If set with Serial Mode 1, then the colour is set from the next character onwards. The background colour can be chosen from all 16 CLUT entries. 45 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TXT: The control character "New background" ("1Dh") is used to change the background colour to the current foreground colour. The selection is immediate ("Set at") and remains valid until the end of the row or until otherwise modified. The TEXT background control characters map to the CLUT entries as shown below: TDA955X/6X/8X PS/N1 series CC: The overline attribute (see Table 18, Serial Mode 0/1, bit 5) is valid from the time set until end of row or otherwise modified. Overlining of Italic characters is not possible. TXT: This attribute is not available. END OF ROW CC: The number of characters in a row is flexible and can determined by the end of row attribute (see Table 18, Serial Mode 1, bit 9). However the maximum number of character positions displayed is determined by the setting of the REG2:Text Position Horizontal and REG4:Text Area End. NOTE: When using the end of row attribute the next character location after the attribute should always be occupied by a 'space'. TXT: This attribute is not available, Row length is fixed at 40 characters. FRINGING A fringe (shadow) can be defined around characters. The fringe direction is individually selectable in any of the North, South, East and West direction using REG3:Fringing Control. The colour of the fringe can also be defined as one of the entries in the CLUT, again using REG3:Fringing Control. CC: The fringe attribute (see Table 18, Serial Mode 0, bit 9) is valid from the time set until the end of the row or otherwise modified. TXT: The display of fringing in TXT mode is controlled by the TXT4.SHADOW bit. When set all the alphanumeric characters being displayed are shadowed, graphics characters are not shadowed. Control Code 00h+1Dh 01h+1Dh 02h+1Dh 03h+1Dh 04h+1Dh 05h+1Dh 06h+1Dh 07h+1Dh Defined Colour Black Red Green Yellow Blue Magenta Cyan White CLUT Entry 8 9 10 11 12 13 14 15 Table 15 Background CLUT mapping BACKGROUND DURATION The attribute when set takes effect from the current position until to the end of the text display defined in REG4:Text Area End. CC: The background duration attribute (see Table 18, Serial Mode 1, bit 8) in combination with the End Of Row attribute (see Table 18, Serial Mode 1, bit 9) forces the background colour to be display on the row until the end of the text area is reached. TXT: This attribute is not available. UNDERLINE The underline attribute causes the characters to have the bottom scan line of the character cell forced to foreground colour, including spaces. If background duration is set, then underline is set until the end of the text area. CC: The underline attribute (see Table 18, Serial Mode 0/1, bit 4) is valid from the time set until end of row or otherwise modified. TXT: This attribute is not available. OVERLINE The overline attribute causes the characters to have the top scan line of the character cell forced to foreground colour, including spaces. If background duration is set, then overline is set until the end of the text area. Fig.16 South and Southwest Fringing MESHING The attribute effects the background colour being displayed. Alternate pixels are displayed as the background colour or video.The structure is offset by 1 46 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller pixel from scan line to scan line, thus achieving a checker board display of the background colour and video. TXT: There are two meshing attributes one that only affects black background colours TXT4.BMESH and a second that only affects backgrounds other than black TXT4.CMESH. A black background is defined as CLUT entry 8, a none black background is defined as CLUT entry 9-15. CC: The setting of the Mesh bit in REG0:Display Control has the effect of meshing any background colour. TDA955X/6X/8X PS/N1 series SPECIAL GRAPHICS CHARACTERS CC/TXT: Several special characters are provided for improved OSD effects. These characters provide a choice of 4 colours within a character cell. The total number of special graphics characters is limited to 16. They are stored in the character codes 8Xh and 9Xh of the character table (32 ROM characters), or in the DRCs which overlay character codes 8Xh and 9Xh. Each special graphics character uses two consecutive normal characters. Fringing, underline and overline is not possible for special graphics characters. Special graphics characters are activated when TXT21.OSD_PLANE = 1. Background Colour "set at" (Mode 0) Serial Attribute Background Colour "set after" (Mode 1) VOLUME Foreground Colour Background Colour Normal Character Foreground Colour 7 Special Character Foreground Colour 6 Fig.17 Meshing and Meshing / Fringing (South+West) CURSOR The cursor operates by reversing the background and foreground colours in the character position pointed to by the active cursor position. The cursor is enabled using TXT7.CURSOR ON. When active, the row the cursor appears on is defined by TXT9.R<4:0> and the column is defined by TXT10.C<5:0>. The position of the cursor can be fixed using TXT9.CURSOR FREEZE. CC: The valid range for row is 0 to 15. The valid range for column is 0 to 47. The cursor remains rectangular at all times, it's shape is not affected by italic attribute, therefore it is not advised to use the cursor with italic characters. TXT: The valid range for row positioning is 0 to 24.The valid range for column is 0 to 39. Fig.19 Special Character Example The example in Fig.19 can be done with 8 special graphics characters. If the screen colour is transparent (implicit in mixed mode) and inside the object the box attribute is set, then the object is surrounded by video. If the box attribute is not set the background colour inside the object will also be displayed as transparent. Plane 10 00 01 10 Colour Allocation Background Colour Foreground Colour CLUT entry 6 CLUT entry 7 ABCDEF Fig.18 Cursor Display 11 Table 16 Special Character Colour allocation 2000 Jun 22 47 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Character and Attribute Coding TDA955X/6X/8X PS/N1 series CC MODE Character coding is split into character oriented attributes (parallel) and character group coding (serial). The serial attributes take effect either at the position of the attribute (Set At), or at the following location (Set After) and remain effective until either modified by a new serial attribute or until the end of the row. A serial attribute is represented as a space (the space character itself however is not used for this purpose), the attributes that are still active, e.g. overline and underline will be visible during the display of the space. The default setting at the start of a row is: * 1x size, flash and italics OFF * overline and underline OFF * Display mode = superimpose * fringing OFF * background colour duration = 0 * end of row = 0 The coding is done in 12 bit words. The codes are stored sequentially in the display memory. A maximum of 768 character positions can be defined for a single display. PARALLEL CHARACTER CODING Bits 0-7 8-10 11 Description 8 bit character code 3 bits for 8 foreground colours Mode bit: 0 = Parallel code Table 17 Parallel Character Coding 2000 Jun 22 48 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller SERIAL CHARACTER CODING TDA955X/6X/8X PS/N1 series Bits Serial Mode 0 ("set at") 0-3 4 4 bits for 16 Background colours 0 = Underline OFF 1 = Underline ON 0 = Overline OFF 1 = Overline ON Display mode: 0 = Superimpose 1 = Boxing 0 = Flash OFF 1 = Flash ON 0 = Italics OFF 1 = Italics ON Description Serial Mode 1 Char.Pos. 1 ("set at") 4 bits for 16 Background colours Horizontal Size: 0 = normal 1 = x2 Vertical Size: 0 = normal 1 = x2 Display mode: 0 = Superimpose 1 = Boxing Foreground colour switch 0 = Bank 0 (colours 0-7) 1 = Bank 1 (colours 8-15) Background colour duration: 0 = stop BGC 1 = set BGC to end of row End of Row 0 = Continue Row 1 = End Row Switch for Serial coding mode 0 and 1: 1 = mode 1 Mode bit: 1 = Serial code Char.Pos. >1 ("set after") 4 bits for 16 Background colours 0 = Underline OFF 1 = Underline ON 0 = Overline OFF 1 = Overline ON Display mode: 0 = Superimpose 1 = Boxing Foreground colour switch 0 = Bank 0 (colours 0-7) 1 = Bank 1 (colours 8-15) Background colour duration (set at): 0 = stop BGC 1 = set BGC to end of row End of Row (set at): 0 = Continue Row 1 = End Row Switch for Serial coding mode 0 and 1: 1 = mode 1 Mode bit: 1 = Serial code (Set At), or at the following location (Set After). The attribute remainseffective until either modified by new serial attributes or until the end of the row.The default settings at the start of a row is: * foreground colour white (CLUT Address 7) * background colour black (CLUT Address 8) 49 5 6 7 8 9 0 = Fringing OFF 1 = Fringing ON Switch for Serial coding mode 0 and 1: 0 = mode 0 10 11 Mode bit: 1 = Serial code Table 18 Serial Character Coding TXT MODE Character coding is in a serial format, with only one attributes being changed at any single location. The serial attributes take effect either at the position of the attribute 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller * Horizontal size x1, Vertical size x1 (normal size) * Alphanumeric ON * Contiguous Mosaic Graphics * Release Mosaics * Flash, Box, Conceal and Twist OFF TDA955X/6X/8X PS/N1 series The attributes have individual codes which are defined in the basic character table below: E/W = 0 bits b7 b6 b5 b4 E/W = 1 111 111 011 101 00 column 0 00 0 0 00 1 1 00 0 b3 b2 b1 b0 000 01 10 1 10 10 1 11 1 1 00 1 1 1 1 0 0 0 01 0 1 101 1 0 0 10 111 111 011 101 0 1 graphics black graphics red graphics green graphics yellow graphics blue graphics magenta graphics cyan graphics white conceal display contiguous graphics separated graphics twist black bkgnd new bkgnd hold graphics release graphics 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0 1 2 3 4 5 6 7 8 9 A B C D E F alpha black alpha red alpha green alpha yellow alpha blue alpha magenta alpha cyan alpha white flash steady end box start box normal height double height double width double size 2 2a 3 3a 4 5 6 6a 7 7a 8 8a 9 9a A Nat Opt Nat Opt OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO S S SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO SS SS DD DD OO OO S S SS DD DD B bkgnd black bkgnd red bkgnd green bkgnd yellow bkgnd blue bkgnd magenta bkgnd cyan bkgnd white C DEF DEF 2000 Jun 22 row Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt Nat Opt norm sz OSD dbl ht OSD dbl wd OSD dbl sz OSD Fig.20 TXT Basic Character Set (Pan-European) 50 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Screen and Global Controls A number of attributes are available that affect the whole display region, and cannot be applied selectively to regions of the display. TV SCAN LINES PER ROW The number of TV scan lines per field used for each display row can be defined, the value is independent of the character size being used. The number of lines can be either 10/13/16 per display row. The number of TV scan lines per row is defined TXT21.DISP_LINES<1:0>. A value of 9 lines per row can be achieved if the display is forced into 525 line display mode by TXT17.DISP_FORCE<1:0>, or if the device is in 10 line mode and the automatic detection circuitry within display finds 525 line display syncs. CHARACTER MATRIX (HXV) There are four different character matrices available, these are 12x10, 12x13, and 12x16. The selection is made using TXT21.CHAR_SIZE<1:0> and is independent of the number of display lines per row. If the character matrix is less than the number of TV scan lines per row then the matrix is padded with blank lines. If the character matrix is greater than the number of TV scan lines then the character is truncated. TDA955X/6X/8X PS/N1 series DISPLAY MODES CC: When attributes superimpose or when boxing (see Table 18, Serial Mode 0/1, bit 6) is set, the resulting display depends on the setting of the following screen control mode bits in REG0:Display Control. Display Mode MOD 10 00 Description Video Video mode disables all display activities and sets the RGB to true black and VDS to video. Full Text mode displays screen colour at all locations not covered by character foreground or background colour. The box attribute has no effect. Mixed Screen mode displays screen colour at all locations not covered by character foreground, within boxed areas or, background colour. Mixed Video mode displays video at all locations not covered by character foreground, within boxed areas or, background colour. Full Text 01 Mixed Screen Colour 10 Mixed Video 11 Table 19 Display Modes TXT: The display mode is controlled by the bits in the TXT5 and TXT6. There are 3 control functions - Text on, Background on and Picture on. Separate sets of bits are used inside and outside Teletext boxes so that different display modes can be invoked. TXT6 is used if the newsflash (C5) or subtitle (C6) bits in row 25 of the basic page memory are set otherwise TXT5 is used. This allows the software to set up the type of display required on newsflash and subtitle pages (e.g. text inside boxes, TV picture outside) this will be invoked without any further software intervention when such a page is acquired. Picture On 0 0 0 1 1 1 Text On 0 1 1 0 1 1 Background On x 0 1 x 0 1 Effect Text mode, black screen Text mode, background always black Text mode Video mode Mixed text and TV mode Text mode, TV picture outside text area Table 20 TXT Display Control Bits 2000 Jun 22 51 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Screen Colour Screen colour is displayed from 10.5 ms to 62.5 ms after the active edge of the HSync input and on TV lines 23 to 310 inclusive, for a 625 line display, and lines 17 to 260 inclusive for a 525 line display. The screen colour is defined by REG0:Display Control and points to a location in the CLUT table. The screen colour covers the full video width. It is visible when the Full Text or Mixed Screen Colour mode is set and no foreground or background pixels are being displayed. Text Display Controls TEXT DISPLAY CONFIGURATION Two types of area are possible. The one area is static and the other is dynamic. The dynamic area allows scrolling of a region to take place. The areas cannot cross each other. Only one scroll region is possible. TDA955X/6X/8X PS/N1 series Display Memory 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Text Area Display possible ROW 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Display Map Entries Enable bit = 0 Soft Scrolling display possible Display possible Display Map The display map allows a flexible allocation of data in the memory to individual rows. Sixteen words are provided in the display memory for this purpose. The lower 10 bits address the first word in the memory where the row data starts. This value is an offset in terms of 16-bit words from the start of Display Memory (8000 Hex). The most significant bit enables the display when not within the scroll (dynamic) area. The display map memory is fixed at the first 16 words in the closed caption display memory. b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Pointer to Row Data Reserved, should be set to 0 Text Display Enable, valid outside Soft Scroll Area 0 = Disable 1 = Enable Fig.21 Display Map and Data Pointers SOFT SCROLL ACTION The dynamic scroll region is defined by the REG5:Scroll Area, REG6:Scroll Range, REG14:Top Scroll line and the REG8:Status Register. The scroll area is enabled when the SCON bit is set in REG8: Status. The position of the soft scroll area window is defined using the Soft Scroll Position (SSP<3:0), and the height of the window is defined using the Soft Scroll Height (SSH<3:0>) both are in REG6:Scroll Range. The rows that are scrolled through the window are defined using the Start Scroll Row (STS<3:0>) and the Stop Scroll Row (SPS<3:0>) both are in REG5:Scroll Area. The soft scrolling function is done by modifying the Scroll Line (SCL<3:0>) in REG14: Top Scroll Line. and the first scroll row value SCR<3:0> in REG8:Status. If the number of rows allocated to the scroll counter is larger than the defined visible scroll area, this allows parts of rows at the top and bottom to be displayed during the scroll function. The registers can be written throughout the field and the values are updated for display with the next field sync. Care should be taken that the register pairs are written to by the software in the same field. Only a region that contains only single height rows or only double height rows can be scrolled. Table 21 Display map Bit Allocation 2000 Jun 22 52 Display Data Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series Soft Scroll Position Pointer SSP<3:0> e.g. 6 Soft Scroll Height SSH<3:0> e.g.4 ROW 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Usable for OSD Display Should not be used for OSD Display Start Scroll Row STS<3:0> e.g. 3 Horizontal Sync. Screen Colour Offset = 8s Vertical Sync. 6 Lines Offset Text Vertical Offset Screen Colour Area Soft Scrolling Area H-Sync delay Should not be used for OSD Display Stop Scroll Row SPS<3:0> e.g. 11 Usable for OSD Display Text Area Fig.22 Soft Scroll Area 0.25 char. offset Text Area Start Text Area End 56s ROW 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0-63 lines row0 Fig.24 Display Area Positioning SCREEN COLOUR DISPLAY AREA This area is covered by the screen colour. The screen colour display area starts with a fixed offset of 8 us from the leading edge of the horizontal sync pulse in the horizontal direction. A vertical offset is not necessary. Horizontal Vertical starts 8 us after the leading edge of H-Sync for 56 us. line 9, field 1 (321, field 2) with respect to leading edge of vertical sync (line numbering using 625 Standard). row1 row2 row3 row4 row5 row6 row7 row8 Closed P01 NBC Scroll Area Offset Captioning data row n Closed Captioning data row n+1 Closed Captioning data row n+2 Closed Captioning data row n+3 Closed Captioning data row n+4 row13 row14 Visible area for scrolling Fig.23 CC Text Areas Display Positioning The display consists of the Screen Colour covering the whole screen and the Text Area that is placed within the visible screen area. The screen colour extends over a large vertical and horizontal range so that no offset is needed. The text area is offset in both directions relative to the vertical and horizontal sync pulses. Table 22 Screen Colour Display Area TEXT DISPLAY AREA The text area can be defined to start with an offset in both the horizontal and vertical direction. Horizontal Up to 48 full sized characters per row. Start position setting from 3 to 64 characters from the leading edge of H-Sync. Fine adjustment in quarter characters. 256 lines (nominal 41- 297). Start position setting from leading edge of vertical sync legal values are 4 to 64 lines. (line numbering using 625 Standard) Vertical Table 23 Text Display Area The horizontal offset is set in REG2: Text Area Start. The offset is done in full width characters using TAS<5:0> and quarter characters using HOP<1:0> for fine setting. The 2000 Jun 22 53 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller values 00h to 03h for TAS<5:0> will result in a corrupted display. The width of the text area is defined in REG4:Text Area End by setting the end character value TAE<5:0>. This number determines where the background colour of the Text Area will end if set to extend to the end of the row. It will also terminate the character fetch process thus eliminating the necessity of a row end attribute. This entails however writing to all positions. The vertical offset is set in REG1:Text Position Vertical Register. The offset value VOL<5:0> is done in number of TV scan lines. NOTE: REG1:Text Position Vertical Register should not be set to 00 Hex as the Display Busy interrupt is not generated in these circumstances. Character Set To facilitate the global nature of the device the character set has the ability to accommodate a large number of characters, which can be stored in different matrices. CHARACTER MATRICES The character matrices that can be accommodated are: (HxVxPlanes) 12x9x1, 12x10x1, 12x13x1, 12x16x1. These modes allow two colours per character position. In CC mode two additional character matrices are available to allow four colours per character: (HxVxPlanes) 12x13x2, 12x16x2. The characters are stored physically in ROM in a matrix of size either 12x10 or 12x16. CHARACTER SET SELECTION Four character sets are available in the device. A set can consist of alphanumeric characters as required by the WST Teletext or FCC Closed Captioning, Customer definable On-Screen Display characters, and Special Graphic characters. CC:- Only a single character set can be used for display and this is selected using the Basic Set selection TXT18.BS<1:0>. When selecting a character set in CC mode the Twist Set selection TXT18.TS<1:0> should be set to the same value as TXT18.BS<1:0> for correct operation. TXT:- Two character sets can be displayed at once. These are the basic G0 set or the alternative G0 set (Twist Set). The basic set is selected using TXT18.BS<1:0>, The alternative/twist character set is defined by TXT19.TS<1:0>. Since the alternative character set is an option it can be enabled or disabled using TXT19.TEN, and the language code that is defined for the alternative set is defined by TXT19.TC<2:0>. TDA955X/6X/8X PS/N1 series ROM ADDRESSING Three ROM's are used to generate the correct pixel information. The first contains the National Option look-up table, the second contains the Basic Character look-up table and the third contains the Character Pixel information. Although these are individual ROM, since they do not need to be accessed simultaneously they are all combined into a single ROM unit. 2400H CHAR PIXEL DATA 71680 x 12 bits Look-Up Set3 Approx. 710 Text or 430Text +176CC Look-Up Set2 0400 Look-Up Set1 0200 Look-Up Set 0 0000H 0000 0600 0800 0800H LOOK-UP Basic + Nat Opt 2048 location Fig.25 ROM Organisation 2000 Jun 22 54 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller CHARACTER TABLE The character table is shown in Table 24:- TDA955X/6X/8X PS/N1 series Character code columns (Bits 4-7) 0 0 1 2 Character code rows (Bits 0-3) 3 4 5 6 7 8 9 A B C D E F a _ e a e i o u 1 (R) 1/2 TM 2 SP ! " # $ % & ( ) a + , . / 3 0 1 2 3 4 5 6 7 8 9 : ; < = > ? 4 @ A B C D E F G H I J K L M N O 5 P Q R S T U V W X Y Z [ e ] i o 6 u a b c d e f g h i j k l m n o N n n 7 p q r s t u v w x y z c 8 9 A B C D E F Table 24 Closed Caption Character Table Special Characters are in column 8. Additional table locations for normal characters Table locations for normal characters Re-definable Characters A number of Dynamically Re-definable Characters (DRC) are available. These are mapped onto the normal character codes, and replace the pre-defined OTP character Rom value. There are 32 DRCs which occupy character codes 80H to 9FH. Alternatively, These locations can be utilized as 16 special graphics characters. The remapping of the standard OSD to the DRCs is activated when the TXT21.DRCS ENABLE bit is set. The selection of Normal or Special OSD symbols is defined by the TXT21.OSD PLANES. Each character is stored in a matrix of 16x16x1 (V x H x planes), this allows for all possible character matrices to be defined within a single location. 2000 Jun 22 55 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series Micro Address 8800 CHAR 0 881F 8820 883F 8840 885F CHAR 1 Char Code 80h CHAR 0 81h CHAR 2 82h A 12 bits 8BC0 8BDF 8BE0 Address 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F DRCs are defined by writing data to the DRC RAM using the 80C51 MOVX command. Setting bits 3 to 9 of the first line of a 12 wide by 16 line character would require setting the high byte of the 80C51 data pointer to 88H, the low byte of the 80C51 data pointer to 00H, using the MOVX command to load address 8800H with data F8H, incrementing the data pointer, and finally using the MOVX command to load address 8801H with data 03H. Display Synchronization The horizontal and vertical synchronizing signals from the TV deflection are used as inputs. Both signals can be inverted before being delivered to the Phase Selector section. CC: The polarity is controlled using either VPOL or HPOL in REG2:Text position Vertical. TXT: SFRs bits TXT1.HPOL & TXT1.VPOL control the polarity. A line locked 12 MHz clock is derived from the 12MHz free running oscillator by the Phase Selector. This line locked clock is used to clock the whole of the Display block. The H & V Sync signals are synchronized with the 12 MHz clock before being used in the display section. Video/Data Switch (Fast Blanking) Polarity The polarity of the Video/Data (Fast Blanking) signal can be inverted. The polarity is set with the VDSPOL in REG7: RGB Brightness register. VDSP OL 0 0 1 VDS Condition CHAR 30 9Eh CHAR 31 8BFF 9Fh Fig.26 Organisation of DRC RAM DEFINING CHARACTERS The DRC RAM is mapped on to the 80C51 RAM address space and starts at location 8800H. The character matrix is 12 bits wide and therefore requires two bytes to be written for each word, the first byte (even addresses), addresses the lower 8 bits and the second byte (odd addresses) addresses the upper 4 bits. For characters of 9, 10 or 16 lines high the pixel information starts in the first address and continues sequentially for the required number of addresses. Characters of 13 lines high are defined with an initial offset of 1 address, this is to allow for correct generation of fringing across boundaries of clustered characters (see Fig.27). The characters continue sequentially for 13 lines after which a further line can again be used for generation of correct fringing across boundaries of clustered characters. Line No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Hex 440 003 00C 030 0C0 300 C00 C00 300 C00 030 00C 003 000 1A8 000 Top Left Pixel MSB 1 0 0 1 RGB display Video Display RGB display Video Display Line 13 from character above LSB Fringing Top Line 1 Table 25 Fast Blanking Signal Polarity Video/Data Switch Adjustment To take into account the delay between the RGB values and the VDS signal due to external buffering, the VDS signal can be moved in relation to the RGB signals. The VDS signal can be set to be either a clock cycle before or after the RGB signal, or coincident with the RGB signal. This is done using VDEL<2:0> in REG15:Configuration. Bottom Line Fringing Line not used Line 1 from character below Bottom Right Pixel Fig.27 13 Line High DRC's Character Format 2000 Jun 22 56 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller RGB Brightness Control A brightness control is provided to allow the RGB upper output voltage level to be modified. The RGB amplitude may be varied between 60% and 100%. The brightness is set in the RGB Brightness register as follows: BRI3-0 0000 ... 1111 RGB Brightness Lowest value ... Highest value TDA955X/6X/8X PS/N1 series This output is intended to act on the TV's display circuits to reduce contrast of the video when it is active. The result of contrast reduction is to improve the readability of the text in a mixed teletext and video display. The bits in the TXT5 & TXT6 SFRs allow the display to be set up so that, for example, the areas inside teletext boxes will be contrast reduced when a subtitle is being displayed but that the rest of the screen will be displayed as normal video. CC: This feature is not available in CC mode. Memory Mapped Registers The memory mapped registers are used to control the display. The registers are mapped into the Microcontroller MOVX address space, starting at address 87F0h and extending to 87FF. MMR MAP Table 26 RGB Brightness Contrast Reduction TXT: The COR bits in SFRs TXT5 & TXT6 control when the COR output of the device is activated (i.e. Pulled-low). ADD R/W 87F0 87F1 R/W R/W Names Display Control Text Position Vertical Text Area Start Fringing Control Text Area End Scroll Area Scroll Range RGB Bright.ness Status read Status write H-Sync. Delay V-Sync. Delay Top Scroll Line Configuration BIT7 SRC<3> VPOL BIT6 SRC<2> HPOL BIT5 SRC<1> VOL<5> BIT4 SRC<0> VOL<4> BIT3 VOL<3> BIT2 MSH VOL<2> BIT1 MOD<1> VOL<1> BIT0 MOD<0> VOL<0> 87F2 87F3 87F4 87F5 87F6 87F7 87F8 87F8 87FC 87FD 87FE 87FF R/W R/W R/W R/W R/W R/W R W R/W R/W R/W R/W HOP<1> FRC<3> SSH<3> SPS<3> VDSPOL BUSY CC HOP<0> FRC<2> SSH<2> SPS<2> FIELD HSD<6> VSD<6> VDEL<2> TAS<5> FRC<1> TAE<5> SSH<1> SPS<1> SCON SCON HSD<5> VSD<5> VDEL<1> TAS<4> FRC<0> TAE<4> SSH<0> SPS<0> FLR FLR HSD<4> VSD<4> VDEL<0> TAS<3> FRDN TAE<3> SSP<3> STS<3> BRI<3> SCR<3> SCR<3> HSD<3> VSD<3> SCL<3> TXT/V TAS<2> FRDE TAE<2> SSP<2> STS<2> BRI<2> SCR<2> SCR<2> HSD<3> VSD<2> SCL<2> - TAS<1> FRDS TAE<1> SSP<1> STS<1> BRI<1> SCR<1> SCR<1> HSD<1> VSD<1> SCL<1> - TAS<0> FRDW TAE<0> SSP<0> STS<0> BRI<0> SCR<0> SCR<0> HSD<0> VSD<0> SCL<0> - Table 27 MMR Memory Map 2000 Jun 22 57 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller MMR BIT DEFINITION TDA955X/6X/8X PS/N1 series Names Display Control. SRC<3:0> MSH BIT7 SRC<3> BIT6 SRC<2> BIT5 SRC<1> BIT4 SRC<0> BIT3 - BIT2 MSH BIT1 MOD<1> BIT0 MOD<0> RESET 00H Screen Colour definition 0 - No meshing of background 1 - Meshing all background colours 00 - Video 01 - Full Text 10 - Mixed Screen Colour 11 - Mixed Video VPOL HPOL VOL<5> VOL<4> VOL<3> VOL<2> VOL<1> VOL<0> 00H MOD<1:0> Text Position Vertical VPOL 0 - Input polarity 1 - Inverted input polarity 0 - Input Polarity 1 - Inverted input polarity Display start Vertical Offset from V-Sync. (lines) HOP<1> HOP<0> TAS<5> TAS<4> TAS<3> TAS<2> TAS<1> TAS<0> 00H HPOL VOL<5:0> Text Area Start HOP<1:0> TAS<5:0> Fringing Control. FRC<3:0> FRDN Fine Horizontal Offset in quarter of characters Text area start FRC<3> FRC<2> FRC<1> FRC<0> FRDN FRDE FRDS FRDW 00H Fringing colour, value address of CLUT 0 - No fringe in North direction 1 - Fringe in North direction 0 - No fringe in East direction 1 - Fringe in East direction FRDE FRDS 0 - No fringe in South direction 1 - Fringe in South direction 0 - No fringe in West direction 1 - Fringe in West direction TAE<5> TAE<4> TAE<3> TAE<2> TAE<1> TAE<0> 00H FRDW Text Area End TAE<5:0> Scroll Area SSH<3:0> SSP<3:0> Scroll Range SPS<3:0> STS<3:0> RGB Brightness Text Area End, in full characters SSH<3> Soft Scroll Height Soft Scroll Position SPS<3> Stop Scroll row Start Scroll row VDSPOL BRI<3> BRI<2> BRI<1> BRI<0> 00H SPS<2> SPS<1> SPS<0> STS<3> STS<2> STS<1> STS<0> 00H SSH<2> SSH<1> SSH<0> SSP<3> SSP<2> SSP<1> SSP<0> 00H 2000 Jun 22 58 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller VDSPOL VDS Polarity 0 - RGB (1), Video (0) 1 - RGB (0), Video (1) RGB Brightness control BUSY BUSY FIELD SCON FLR SCR<3> TDA955X/6X/8X PS/N1 series BRI<3:0> Status read SCR<2> SCR<1> SCR<0> 00H 0 - Access to display memory will not cause display problems 1 - Access to display memory could cause display problems. 0 - Odd Field 1 - Even Field 0 - Active flash region foreground and background displayed 1 - Active flash region background only displayed First scroll row SCON FLR SCR<3> SCR<2> SCR<1> SCR<0> 00H FIELD FLR SCR<3:0> Status write SCON 0 - Scroll area disabled 1 - Scroll area enabled 0 - Active flash region foreground and background colour displayed 1 - Active flash region background colour only displayed First Scroll Row HSD<6> HSD<5> HSD<4> HSD<3> HSD<3> HSD<1> HSD<0> 00H FLR SCR<3:0> H-Sync. delay HSD<6:0> V-Sync Delay VSD<6:0> Top Scroll Line SCL<3:0> Configuration CC H-Sync delay, in full size characters VSD<6> VSD<5> VSD<4> VSD<3> VSD<2> VSD<1> VSD<0> 00H V-Sync delay in number of TV lines Top line for scroll CC VDEL<2> VDEL<1> VDEL<0> TXT/V 00H SCL<3> SCL<2> SCL<1> SCL<0> 00H 0 - OSD mode 1 - Closed Caption mode Pixel delay between VDS and RGB output 000 - VDS switched to video, not active 001 - VDS active one pixel earlier then RGB 010 - VDS synchronous to RGB 100 - VDS active one pixel after RGB BUSY Signal switch 1 - Horizontal 0 - Vertical VDEL<2:0> TXT/V Table 28 MMR Descriptions 2000 Jun 22 59 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller OTP MEMORY These may be programmed either using the Parallel Programming Interface or via the ISP Programming Interface. Parallel Programming The following pins form the parallel programming interface:- TDA955X/6X/8X PS/N1 series security bits are one-time programmable and CANNOT be erased. Pin P0.5 P0.6 P1.0 P1.1 P1.2 P1.3 P3.1 P3.2 P2.0 Name IO(0) IO(1) IO(2) IO(3) IO(4) IO(5) IO(6) IO(7) OEB Function Bit 0:- Address/Data/Mode Bit 1:- Address/Data/Mode Bit 2:- Address/Data/Mode Bit 3:- Address/Data/Mode Bit 4:- Address/Data/Mode Bit 5:- Address/Data/Mode Bit 6:- Address/Data/Mode Bit 7:- Address/Data/Mode Output Enable 0 = IO is output 1 = IO is input Write Enable, programming pulse >100us 0 = Program 0 = IO(7:0) defined by A/DB 1 = IO(7:0) contains mode information 0 = IO(7:0) contains Data 1 = IO(7:0) contains Information Unused P3.0 WEB P1.6 MODE P1.7 A/DB Address P3.3 VPE RESET XTALIN VPE RESET CLK 9V Programming Voltage Device reset/ mode selection Clock 4 MHz Table 29 Parallel Programming Interface ISecurity Bits The family of devices have a set of security bits for the combined OTP Program ROM, Character ROM and Packet 26 ROM. The security bits are used to prevent the ROM from being overwritten once programmed, and also the contents being verified once programmed. The 2000 Jun 22 60 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller The memory and security bits are structured as follows:- TDA955X/6X/8X PS/N1 series MEMORY PROGRAM ROM USER ROM (i.e. 128k x 8 bits) TEST ROM RESERVED (1k x 8 bits) = USER ROM Programming (Enable/Disable) Yes SECURITY BITS INTERACTION TEST ROM Programming (Enable/Disable) No Verify (Enable/Disable) Yes = No Yes Yes CHARACTER ROM USER ROM (9k x 12 bits) TEST ROM RESERVED (0.5k x 12 bits) = USER ROM Programming (Enable/Disable) Yes TEST ROM Programming (Enable/Disable) No Verify (Enable/Disable) Yes = No Yes Yes PACKET 26 ROM USER ROM (4k x 8 bits) = USER ROM Programming (Enable/Disable) Yes TEST ROM Programming (Enable/Disable) No Verify (Enable/Disable) Yes Table 30 Security bit structure The security bits are set as follows for production programmed devices (i.e. programmed by Philips):- MEMORY USER ROM Programming (Enable/Disable) PROGRAM ROM CHARACTER ROM PACKET 26 ROM = = = DISABLED DISABLED DISABLED SECURITY BITS SET TEST ROM Programming (Enable/Disable) DISABLED DISABLED DISABLED Verify (Enable/Disable) ENABLED ENABLED ENABLED Table 31 Security bits for production devices The security bits are set as follows for production un-programmed (blank) devices:- MEMORY USER ROM Programming (Enable/Disable) PROGRAM ROM CHARACTER ROM PACKET 26 ROM = = = ENABLED ENABLED ENABLED SECURITY BITS SET TEST ROM Programming (Enable/Disable) DISABLED DISABLED DISABLED Verify (Enable/Disable) ENABLED ENABLED ENABLED Table 32 Security bits for Blank devices 2000 Jun 22 61 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 2000 Jun 22 62 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller FUNCTIONAL DESCRIPTION OF VIDEO PROCESSOR Vision IF amplifier The vision IF amplifier can demodulate signals with positive and negative modulation. The PLL demodulator is completely alignment-free. The VCO of the PLL circuit is internal and the frequency is fixed to the required value by using the clock frequency of the -Controller/Teletext decoder as a reference. The setting of the various frequencies (38, 38.9, 45.75 and 58.75 MHz) can be made via the control bits IFA-IFC in subaddress 27H. Because of the internal VCO the IF circuit has a high immunity to EMC interferences. QSS Sound circuit The sound IF amplifier is similar to the vision IF amplifier and has an external AGC decoupling capacitor. The single reference QSS mixer is realised by a multiplier. In this multiplier the SIF signal is converted to the intercarrier frequency by mixing it with the regenerated picture carrier from the VCO. The mixer output signal is supplied to the output via a high-pass filter for attenuation of the residual video signals. With this system a high performance hi-fi stereo sound processing can be achieved. The AM sound demodulator is realised by a multiplier. The modulated sound IF signal is multiplied in phase with the limited SIF signal. The demodulator output signal is supplied to the output via a low-pass filter for attenuation of the carrier harmonics. The AM signal is supplied to the output (AUDOUT/AMOUT) via the volume control. Switching between the QSS output and AM output is made by means of the AM bit in subaddress 29H (see also Table 1). FM demodulator The FM demodulator is realised as narrow-band PLL with external loop filter, which provides the necessary selectivity without using an external band-pass filter. To obtain a good selectivity a linear phase detector and a constant input signal amplitude are required. For this reason the intercarrier signal is internally supplied to the demodulator via a gain controlled amplifier and AGC circuit. To improve the selectivity an internal bandpass filter is connected in front of the PLL circuit. This bandpass filter can be switched off by means of the BPB bit in subaddress 2CH. TDA955X/6X/8X PS/N1 series The nominal frequency of the demodulator is tuned to the required frequency (4.5/5.5/6.0/6.5 MHz) by means of a calibration circuit which uses the clock frequency of the -Controller/Teletext decoder as a reference. It is also possible to frequencies of 4.74 and 5.74 MHz so that a second sound channel can be demodulated. In the latter application an external bandpass filter has to be applied to obtain sufficient selectivity (the sound input can be activated by the SIF bit in subaddress 28H). The setting to the wanted frequency is realised by means of the control bits FMA, FMB and FMC in the control bit 29H. From the output status bytes it can be read whether the PLL frequency is inside or outside the window and whether the PLL is in lock or not. With this information it is possible to make an automatic search system for the incoming sound frequency. This can be realised by means of a software loop which switches the demodulator to the various frequencies and then select the frequency on which a lock condition has been found. The deemphasis output signal amplitude is independent of the TV standard and has the same value for a frequency deviation of 25 kHz at the 4.5 MHz standard and for a deviation of 50 Khz for the other standards. In versions with QSS amplifier and mono intercarrier sound circuit the FM radio mode is available. This mode is activated by means of the FMR-bit (subaddress 2CH). The selectivity must be made by means of a SAW filter at the sound input with a centre frequency of 33.4 MHz for Europe and 41.25 MHz for the USA. For this application the IF demodulator must be set to a fixed frequency (42 MHz for Europe and 48 MHz for the USA). The resulting input frequency for the FM demodulator is then 8.6 MHz for Europe and 6.75 MHz for the USA. This frequency must be selected by means of the bits FMA, FMB and FMC (see table 108). Audio circuit and input signal selection The audio control circuit contains an audio switch with 1 external input and a volume control circuit. The selection of the various inputs is made by means of the ADX bit. In various versions the Automatic Volume Levelling (AVL) function can be activated. The pin to which the external capacitor has to be connected depends on the IC version. For the 90 types the capacitor is connected to the EW output pin. For the 110 types a choice must be made between the AVL function and a sub-carrier output for comb filter applications. This choice is made via the CBM0/1 bits (in subaddress 22H). When the AVL is active it automatically stabilises the audio output signal to a certain level. 2000 Jun 22 63 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller It is possible to use the deemphasis pin as additional audio input. In that case the internal signal must, of course, be switched off. This can be realised by means of the sound mute bit (SM in subaddress 29H). When the IF circuit is switched to positive modulation the internal signal on the deemphasis pin is automatically muted. CVBS and Y/C input signal selection The circuit has 2 inputs for external CVBS signals and one input can also be used as one Y/C input (see Fig. 27). It is possible to supply the selected CVBS signal to the demodulated IF video output pin. This mode is selected by means of the SVO bit in subaddress 22H. The vision IF amplifier is switched off in this mode. TDA955X/6X/8X PS/N1 series The video ident circuit can be connected to the incoming `internal' video signal or to the selected signal. This ident circuit is independent of the synchronisation and can be used to switch the time-constant of the horizontal PLL depending on the presence of a video signal (via the VID bit). In this way a very stable OSD can be realised. The subcarrier output is combined with a 3-level output switch (0 V, 2.3 V and 4.5 V). The output level and the availability of the subcarrier signal is controlled by the CMB1 and CMB0 bits. The output can be used to switch sound traps etc. It is also possible to use this pin for the connection of the AVL capacitor or as AM output. TO LUMA/SYNC PROCESSING IDENT VIM TO CHROMA PROCESSING (+) VIDEO IDENT IFVO SVO CVBS1 CVBS2/Y C IFVO/SVO Fig.27 CVBS switch and interfacing of video ident Synchronisation circuit The IC contains separator circuits for the horizontal and vertical sync pulses and a data-slicing circuit which extracts the digital teletext data from the analog signal. The horizontal drive signal is obtained from an internal VCO which is running at a frequency of 25 MHz. This oscillator is stabilised to this frequency by using a 12 MHz signal coming from the reference oscillator of the -Controller/Teletext decoder. The horizontal drive is switched on and off via the soft start/stop procedure. This function is realised by means of variation of the TON of the horizontal drive pulses. In addition the horizontal drive circuit has a `low-power start-up' function. 2000 Jun 22 64 The vertical synchronisation is realised by means of a divider circuit. The vertical ramp generator needs an external resistor and capacitor. For the vertical drive a differential output current is available. The outputs must be DC coupled to the vertical output stage. In the types which are intended for 90 picture tubes the following geometry parameters can be adjusted: * Horizontal shift * Vertical amplitude * Vertical slope * S-correction * Vertical shift Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller The types which are intended to be used in combination with 110 picture tubes have an East-West control circuit in stead of the AVL function. The additional controls for these types are: * EW width * EW parabola width * EW upper and lower corner parabola correction * EW trapezium correction * Vertical zoom * horizontal parallelogram and bow correction. When the vertical amplitude is compressed (zoom factor <1) it is still possible to display the black current measuring lines in the overscan. This function is activated by means of the bit OSVE in subaddress 26H. Chroma, luminance and feature processing The chroma band-pass and trap circuits (including the SECAM cloche filter) are realised by means of gyrators and are tuned to the right frequency by comparing the tuning frequency with the reference frequency of the colour decoder. The luminance delay line and the delay cells for the peaking circuit are also realised with gyrators. The circuit contains the following picture improvement features: * Video dependent coring in the peaking circuit. The coring can be activated only in the low-light parts of the screen. This effectively reduces noise while having maximum peaking in the bright parts of the picture. * Black stretch. This function corrects the black level for incoming signals which have a difference between the black level and the blanking level. * Blue-stretch. This circuit is intended to shift colour near `white' with sufficient contrast values towards more blue to obtain a brighter impression of the picture. * Dynamic skin tone (flesh) control. This function is realised in the YUV domain by detecting the colours near to the skin tone. TDA955X/6X/8X PS/N1 series Colour decoder The ICs can decode PAL, NTSC and SECAM signals. The PAL/NTSC decoder does not need external reference crystals but has an internal clock generator which is stabilised to the required frequency by using the 12 MHz clock signal from the reference oscillator of the -Controller/Teletext decoder. Under bad-signal conditions (e.g. VCR-playback in feature mode), it may occur that the colour killer is activated although the colour PLL is still in lock. When this killing action is not wanted it is possible to overrule the colour killer by forcing the colour decoder to the required standard and to activate the FCO-bit (Forced Colour On) in subaddress 21H. The Automatic Colour Limiting (ACL) circuit (switchable via the ACL bit in subaddress 20H) prevents that oversaturation occurs when signals with a high chroma-to-burst ratio are received. The ACL circuit is designed such that it only reduces the chroma signal and not the burst signal. This has the advantage that the colour sensitivity is not affected by this function. The SECAM decoder contains an auto-calibrating PLL demodulator which has two references, viz: the divided 12 MHz reference frequency (obtained from the -Controller) which is used to tune the PLL to the desired free-running frequency and the bandgap reference to obtain the correct absolute value of the output signal. The VCO of the PLL is calibrated during each vertical blanking period, when the IC is in search or SECAM mode. The base-band delay line (TDA 4665 function) is integrated. This delay line is also active during NTSC to obtain a good suppression of cross colour effects. The demodulated colour difference signals are internally supplied to the delay line. 2000 Jun 22 65 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller RGB output circuit and black-current stabilization In the RGB control circuit the signal is controlled on contrast, brightness and saturation. The ICs have a linear input for external RGB/YUV signals. Switching between RGB and the YUV/YPRPB mode can be realised via the YUV0/YUV1 bits in subaddress 2BH. The signals for OSD and text are internally supplied to the control circuit. The output signal has an amplitude of about 2 V black-to-white at nominal input signals and nominal settings of the various controls. To obtain an accurate biasing of the picture tube the `Continuous Cathode Calibration' system has been included in these ICs. A black level off-set can be made with respect to the level which is generated by the black current stabilization system. In this way different colour temperatures can be obtained for the bright and the dark part of the picture. In the Vg2 adjustment mode (AVG = 1) the black current stabilization system checks the output level of the 3 channels and indicates whether the black level of the highest output is in a certain window (WBC-bit) or below or above this window (HBC-bit). This indication can be read from the status byte 01 and can be used for automatic adjustment of the Vg2 voltage during the production of the TV receiver. During this test the vertical scan remains active so that the indication of the 2 bits can be made visible on the TV screen. The control circuit contains a beam current limiting circuit and a peak white limiting circuit. The peak white level is adjustable via the I2C-bus. To prevent that the peak white limiting circuit reacts on the high frequency content of the video signal a low-pass filter is inserted in front of the peak detector. The circuit also contains a soft-clipper which prevents that the high frequency peaks in the output signal become too high. The difference between the peak white limiting level and the soft clipping level is adjustable via the I2C-bus in a few steps. During switch-off of the TV receiver a fixed beam current is generated by the black current control circuit. This current ensures that the picture tube capacitance is discharged. During the switch-off period the vertical deflection can be placed in an overscan position so that the discharge is not visible on the screen. A wide blanking pulse can be activated in the RGB outputs by means of the HBL bit in subaddress 2BH. The timing of this blanking can be adjusted by means of the bits WBF/R bits in subaddress 03H. TDA955X/6X/8X PS/N1 series SOFTWARE CONTROL The CPU communicates with the peripheral functions using Special function Registers (SFRs) which are addressed as RAM locations. The registers for the Teletext decoder appear as normal SFRs in the -Controller memory map and are written to these functions by using a serial bus. This bus is controlled by dedicated hardware which uses a simple handshake system for software synchronisation. For compatibility reasons and possible re-use of software blocks, the I2C-bus control for the TV processor is organised as in the stand-alone TV signal processors. The TV processor registers cannot be read, so when the content of these registers is needed in the software, a copy should be stored in Auxiliary RAM or Non Volatile RAM. The slave address of the TV signal processor is given in Fig.28. handbook, halfpage A6 1 A5 0 A4 0 A3 0 A2 1 A1 0 A0 1 R/W 1/0 MLA743 Fig.28 Slave address (8A). Valid subaddresses: 03H to 2EH, subaddress FE and FF are reserved for test purposes. Auto-increment mode available for subaddresses. 2000 Jun 22 66 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller DESCRIPTION OF THE I2C-BUS SUBADDRESSES Table 33 Inputs TV-processor FUNCTION Timing of `wide blanking' Peak white limiting Off-set IF demodulator Horizontal parallelogram Horizontal bow Hue Horizontal shift (HS) EW width (EW) (1) EW parabola/width (PW) (1) EW upper corner parabola(1) EW lower corner parabola(1) EW trapezium (TC) (1) Vertical slope (VS) Vertical amplitude (VA) S-correction (SC) Vertical shift (VSH) Vertical zoom (VX) (1) Black level offset R Black level offset G White point R White point G White point B Peaking Luminance delay time Brightness Saturation Contrast AGC take-over Volume control Colour decoder 0 Colour decoder 1 AV-switch 0 AV-switch 1 Synchronisation 0 Synchronisation 1 Deflection Vision IF 0 Vision IF 1 Sound 0 Control 0 Control 1 Sound 1 Features 0 Features 1 Note SUBADDR (HEX) D7 D6 D5 03 WBF3 WBF2 WBF1 04 0 0 SOC1 05 0 0 A5 06 0 0 A5 07 0 0 A5 08 0 0 A5 09 0 0 A5 0A 0 0 A5 0B 0 0 A5 0C 0 0 A5 0D 0 0 A5 0E 0 0 A5 0F 0 0 A5 10 0 0 A5 11 0 0 A5 12 0 0 A5 13 0 0 A5 14 0 0 A5 15 0 0 A5 16 0 0 A5 17 0 0 A5 18 0 0 A5 19 PF1 PF0 A5 1A 0 0 0 1B 0 0 A5 1C 0 0 A5 1D 0 0 A5 1E 0 0 A5 1F 0 0 A5 20 CM3 CM2 CM1 21 0 0 0 22 0 0 SVO 23 0 0 0 24 0 HP2 FOA 25 0 0 FSL 26 OSVE AFN DFL 27 IFA IFB IFC 28 SIF IFE AGCM 29 AGN SM1 FMWS 2A 0 IE2 RBL 2B 0 0 0 2C FMD 0 ADX 2D 0 0 COR1 2E 0 0 RPO1 TDA955X/6X/8X PS/N1 series DATA BYTE D4 D3 WBF0 WBR3 SOC0 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 0 YD3 A4 A3 A4 A3 A4 A3 A4 A3 A4 A3 CM0 MAT 0 0 CMB1 CMB0 0 0 FOB POC OSO FORF XDT SBL VSW MOD IFLH AMFM AM(3) SM0 AKB CL3 SOY 0 0 FMR COR0 DSK RPO0 0 D2 WBR2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 YD2 A2 A2 A2 A2 A2 MUS 0 INA E2D STB FORS AVG AFW AGC1 FMC CL2 YUV1 AVL(2) 0 0 POR D1 D0 Value WBR1 WBR0 88 A1 A0 08 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 00 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 YD1 YD0 00 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 A1 A0 20 ACL CB 00 BPS FCO 00 INB INC 00 0 RGBL 00 VIM VID 00 DL NCIN 00 EVG HCO(1) 00 IFS STM 00 AGC0 FFI 00 FMB FMA 00 CL1 CL0 00 YUV0 HBL(1) 00 QSS FMI 00 BLS BKS 00 0 0 00 1. These functions are only available in versions which have the East-West drive output. 2. The AVL function is only available in versions which have no East-West output or when the subcarrier output is used for the connection of the AVL capacitor (via the bits CMB1 and CMB0 in subaddress 22H). 3. Only available in types with QSS sound IF circuit and AM demodulator. 2000 Jun 22 67 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 34 Outputs TV-processor TDA955X/6X/8X PS/N1 series DATA BYTE FUNCTION Output status bytes SUBADDR D7 00 01 02 03 04 POR XPR SUP ID7 SN1 D6 IFI NDF AGC ID6 SN0 D5 LOCK FSI 0 ID5 X D4 SL IVW QSS ID4 X D3 CD3 WBC AFA ID3 X D2 CD2 HBC AFB ID2 X D1 CD1 BCF FMW ID1 X D0 CD0 IN2 FML ID0 X Explanation input control data TV-processor Table 35 Timing of `wide blanking' DAC SETTING 0 0F 3.5 / 7.8 s 5.9 / 10.2 s SETTING Table 39 Horizontal parallelogram DAC SETTING 0 CONTROL screen top 0.5 s delayed and screen bottom 0.5 s advanced with respect to centre no correction screen top 0.5 s advanced and screen bottom 0.5 s delayed with respect to centre Horizontal bow CONTROL screen top and bottom 0.5 s delayed with respect to centre no correction screen top and bottom 0.5 s advanced with respect to centre Hue control CONTROL -45 0 +45 Horizontal shift CONTROL -2 s 0 +2 s 20 3F Table 36 Soft clipping level SOC1 0 0 1 1 SOC0 0 1 0 1 VOLTAGE DIFFERENCE BETWEEN SOFT CLIPPING AND PWL 0% above PWL level 5% above PWL level 10% above PWL level soft clipping off Table 40 DAC SETTING 0 20 Table 37 Peak White Limiting; note 1 DAC SETTING 00 0F Note 1. CVBS/Y input signal at which the Peak White Limiting is activated. Nominal input signal: 1.0 VBL-WH. Table 38 Off-set IF demodulator 0.55 VBL-WH 0.85 VBL-WH CONTROL 3F Table 41 DAC SETTING 0 20 3F Table 42 DAC SETTING 0 20 3F tbf no correction tbf CONTROL DAC SETTING 0 20 3F 2000 Jun 22 68 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 43 EW width CONTROL output current 700 A output current 0 A EW parabola/width CONTROL output current 0 A output current 440 A at top and bottom of screen EW upper/lower corner parabola CONTROL output current +76 A output current 0 A output current -207 A EW trapezium CONTROL output current at top of screen 100 A lower that at bottom no correction output current at top of screen 100 A higher than at bottom Vertical slope CONTROL correction -20% no correction correction +20% Vertical amplitude Table 55 DAC SETTING 0 20 3F Table 49 CONTROL amplitude 80% amplitude 100% amplitude 120% S-correction CONTROL correction -10% no correction correction 25% 69 Table 51 Table 50 TDA955X/6X/8X PS/N1 series Vertical shift CONTROL shift -5% no correction shift +5% Vertical zoom CONTROL amplitude 75% amplitude 100% amplitude 138% Black level off-set R/G CONTROL off-set of -160 mV no off-set off-set of +160 mV White point R/G/B CONTROL gain -3 dB no correction gain +3 dB Peaking centre frequency PF0 0 1 0 1 CENTRE FREQUENCY 2.7 MHz 3.1 MHz 3.5 MHz spare DAC SETTING 0 3F Table 44 DAC SETTING 0 20 3F DAC SETTING 0 3F DAC SETTING 0 20 3F Table 52 Table 45 DAC SETTING 0 11 3F Table 46 DAC SETTING 0 20 3F Table 53 DAC SETTING 0 20 3F DAC SETTING 0 20 3F Table 54 PF1 0 0 1 1 Table 47 DAC SETTING 0 20 3F Table 48 Peaking control (overshoot in direction `black') CONTROL depeaking (overshoot -22%) no peaking overshoot 80% DAC SETTING 0 10 3F DAC SETTING 0 0E 3F 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 56 Y-delay adjustment; note 1 Y-DELAY YD3 x 160 ns + YD2 x 80 ns + YD1 x 80 ns + YD0 x 40 ns Table 62 TDA955X/6X/8X PS/N1 series Colour decoder mode, note 1 DECODER MODE PAL/NTSC/SECAM PAL/SECAM PAL NTSC SECAM PAL/NTSC PAL NTSC PAL/NTSC/SECAM PAL/NTSC PAL NTSC PAL/NTSC (Tri-Norma) PAL/NTSC PAL NTSC B B B ABCD C C C BCD D D D FREQ A A A A YD0 to YD3 YD3 YD2 YD1 YD0 Note CM3 CM2 CM1 CM0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1. For an equal delay of the luminance and chrominance signal the delay must be set at a value of 160 ns. This is only valid for a CVBS signal without group delay distortions. Table 57 Brightness control CONTROL correction -0.7V no correction correction +0.7V Saturation control CONTROL colour off (-52 dB) saturation nominal saturation +300% Contrast control CONTROL RGB amplitude -14 dB RGB amplitude nominal RGB amplitude +6 dB AGC take-over CONTROL tuner take-over at IF input signal of 0.4 mV tuner take-over at IF input signal of 80 mV Volume control CONTROL attenuation 80 dB no attenuation DAC SETTING 0 20 3F Table 58 1 1 1 1 1 Note DAC SETTING 0 17 3F Table 59 1. The decoder frequencies for the various standards are obtained from an internal clock generator which is synchronised by a 12 MHz reference signal which is obtained from the -Controller clock generator. These frequencies are: a) A: 4.433619 MHz b) B: 3.582056 MHz (PAL-N) c) C: 3.575611 MHz (PAL-M) d) D: 3.579545 MHz (NTSC-M) Table 63 MAT 0 1 Table 64 MUS PAL matrix NTSC matrix MATRIX POSITION Japanese matrix USA matrix PAL-SECAM/NTSC matrix MATRIX POSITION adapted to standard DAC SETTING 0 20 3F Table 60 DAC SETTING 0 3F Table 61 0 1 DAC SETTING 0 3F 2000 Jun 22 70 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 65 ACL 0 1 Table 66 CB 0 1 Table 67 BPS 0 1 Table 68 FCO 0 1 off on active bypassed Forced Colour-On CONDITION FSC 1.1 x FSC Bypass of chroma base-band delay line DELAY LINE MODE not active active Chroma bandpass centre frequency CENTRE FREQUENCY Note Automatic colour limiting COLOUR LIMITING TDA955X/6X/8X PS/N1 series Table 72 Selection of audio output signal on AUDEEM pin, note 1 E2D 0 1 MODE deemphasis (front-end audio available) selected audio signal available 1. This function can be activated only when the MOD bit is 0. Table 73 Blanking of RGB outputs RGBL 0 1 CONDITION normal operation RGB outputs blanked continuously Table 74 Synchronization of OSD/TEXT display HP2 0 1 Table 75 FOA 0 0 1 1 -CONTROLLER COUPLED TO 1 loop 2 loop Phase 1 (1) time constant FOB 0 1 0 1 normal slow slow/fast fast MODE Table 69 Selected video out (pin 38) SVO 0 1 CONDITION IF video available at output selected CVBS available at output Table 70 Condition AVL/SNDIF/REFO/REFIN (pin 27) CMB1 CMB0 0 0 1 1 0 1 0 1 CONDITION AVL/SNDIF active (depends on SIF bit) output voltage 2.3 V + subcarrier; output voltage 0 V output voltage 4.5V Table 77 Table 71 Source select INA 0 0 1 INB 0 1 0 INC 0 0 0 SELECTED SIGNALS CVBS1 CVBS2 Y/C Table 78 VIM 0 1 Video ident mode MODE ident coupled to internal CVBS (pin 40) ident coupled to selected CVBS STB 0 1 stand-by normal Stand-by MODE Table 76 POC 0 1 active not active Synchronization mode MODE 2000 Jun 22 71 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 79 VID 0 1 not active Video ident mode VIDEO IDENT MODE 1 loop switched on and off TDA955X/6X/8X PS/N1 series Table 86 AFC switch AFN 0 1 normal operation AFC not active MODE Table 80 Forced slicing level for vertical sync FSL 0 1 Table 81 OSO 0 1 Table 82 FORF 0 0 1 1 Table 83 DL 0 1 Table 84 NCIN 0 1 interlace de-interlace Vertical divider mode VERTICAL DIVIDER MODE normal operation switched to search window SLICING LEVEL slicing level dependent on noise detector fixed slicing level of 70% Switch-off in vertical overscan MODE Switch-off undefined Switch-off in vertical overscan Forced field frequency FORS 0 1 0 1 Interlace STATUS 60 Hz keep last detected field frequency auto (50 Hz when line not in sync) FIELD FREQUENCY auto (60 Hz when line not in sync) Table 87 Disable flash protection DFL 0 1 MODE flash protection active flash protection disabled Table 88 X-ray detection XDT 0 MODE protection mode, when a too high EHT is detected the receiver is switched to stand-by and the XPR-bit is set to 1 detection mode, the receiver is not switched to stand-by and only the XPR-bit is set to 1 1 Table 89 Service blanking SBL 0 1 Table 90 AVG 0 1 normal operation Vg2 adjustment (WBC and HBC bits in output byte 01 can be read) Enable vertical guard (RGB blanking) VERTICAL GUARD MODE not active active EHT tracking mode TRACKING MODE EHT tracking only on vertical EHT tracking on vertical and EW off on Adjustment Vg2 voltage MODE SERVICE BLANKING MODE Table 91 EVG 0 1 Table 92 HCO 0 1 Table 85 Black current measuring lines in overscan (for vertical zoom setting < 1) OSVE 0 1 normal operation measuring lines in overscan MODE 2000 Jun 22 72 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 93 IFE 0 0 0 0 0 0 0 0 1 Table 94 VSW 0 1 Table 95 MOD 0 1 Table 96 AFW 0 1 Table 97 IFS 0 1 Table 98 STM 0 1 Table 99 SIF 0 1 normal operation reduced sensitivity of video indent circuit Selection external input for sound IF circuit MODE IF input not selected IF input selected (see also table 1) normal reduced Search tuning mode MODE normal enlarged IF sensitivity IF SENSITIVITY negative positive AFC window AFC WINDOW normal operation IF-video signal switched off Modulation standard MODULATION PLL demodulator frequency adjust IFA 0 0 0 0 1 1 1 1 X IFB 0 0 1 1 0 1 0 1 X IFC 0 1 0 1 0 0 1 1 X IF FREQUENCY 58.75 MHz 45.75 MHz 38.90 MHz 38.00 MHz 33.40 MHz 33.90 MHz 42.00 MHz 48.00 MHz external reference carrier TDA955X/6X/8X PS/N1 series Table 100Calibration of IF PLL demodulator IFLH 0 1 MODE calibration system active calibration system not active Table 101AM/FM operation (QSS versions); AMFM 0 1 CONDITION normal operation FM demodulator activated Table 102IF AGC speed AGC1 AGC0 0 1 0 1 0.7 x norm norm 3 x norm 6 x norm AGC SPEED Video mute STATE 0 0 1 1 Table 103 Fast filter IF-PLL FFI 0 1 CONDITION normal time constant increased time constant Table 104 Gain FM demodulator AGN 0 1 MODE normal operation gain +6 dB, to be used for the demodulation of mono signals in the NTSC system Table 105Sound mute SM1 0 1 1 Note 1. The mute is activated when the digital acquisition help is out-of-window. Table 106Window selection of Narrow-band sound PLL FMWS 0 1 small window large window FUNCTION SM0 1 0 1 see note 1 mute on mute off CONDITION 2000 Jun 22 73 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 107 Selection QSS out or AM out AM 0 1 MODE QSS output selected AM output selected 0 Table 108 Nominal frequency FM demodulator FMC 0 0 0 0 1 1 1 1 FMB 0 0 1 1 0 0 1 1 FMA 0 1 0 1 0 1 0 1 FREQUENCY 5.5 MHz 6.0 MHz 4.5 MHz 6.5 MHz 5.74 MHz 6.75 MHz 4.74 MHz 8.60 MHz 0 1 Note CL3 TDA955X/6X/8X PS/N1 series Table 113 Cathode drive level (15 steps; 3.5 V/step) CL2 0 1 1 CL1 0 1 1 CL0 0 1 1 SETTING CATHODE DRIVE AMPLITUDE; NOTE 1 50 VBL-WH 75 VBL-WH 95 VBL-WH 1. The given values are valid for the following conditions: a) - Nominal CVBS input signal b) - Nominal settings for contrast, WPA and peaking c) - Black- and blue-stretch switched-off d) - Gain of output stage such that no clipping occurs e) - Beam current limiting not active f) The tolerance on these values is about 3 V. Table 114Synchronisation on YUV input SOY 0 1 MODE sync coupled to CVBS (Y) input sync coupled to Y input Table 109 FM demodulator at 10.7 MHz FMD 0 1 MODE frequency FM demodulator determined by the bits FMA, FMB and FMC frequency FM demodulator 10.7 MHz Table 115RGB/YUV switch Table 110Enable fast blanking ext.RGB/YUV IE2 0 1 not active active FAST BLANKING YUV1 0 0 1 1 Note 1. YUV input with the specification: Y = +1.4 VP-P; U = -1.33 VP-P; V = -1.05 VP-P. These signal amplitudes are based on a colour bar signal with 75% saturation. 2. YPRPB input with the specification: Y = +1.0 VP-P; PB = +0.7 VP-P; PR = +0.7 VP-P. These signal amplitudes are based on a colour bar signal with 100% saturation. Table 116 RGB blanking mode (110 types) HBL 0 1 wide blanking MODE normal blanking (horizontal flyback) MODE active not active YUV0 0 1 0 1 MODE RGB input activated spare YUV input; input conditions: note 1 YPRPB input; input conditions: note 2 Table 111 RGB blanking RBL 0 1 not active active RGB BLANKING Table 112 Black current stabilization AKB 0 1 2000 Jun 22 74 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 117Audio signal selection ADX 0 1 SELECTED SIGNAL internal audio signal external audio signal TDA955X/6X/8X PS/N1 series Table 122Video dependent coring (peaking) COR1 0 0 1 1 COR0 0 1 0 1 off coring active between 0 and 20 IRE coring active between 0 and 40 IRE coring active between 0 and 100 IRE SETTING Table 118FM radio function enabled FMR 0 1 TV mode FM radio mode MODE Table 123Dynamic skin control on/off DSK 0 1 off on MODE Table 119Auto Volume Levelling AVL 0 1 not active active MODE Table 124 Blue stretch BLS 0 off on 1 BLUE STRETCH MODE Table 120Mode of Quasi Split Sound amplifier QSS 0 1 MODE QSS amplifier not active, input of sound PLL connected to vision IF amplifier output QSS amplifier active, output connected to QSSO or to input sound PLL (via FMI bit) Table 125 Black stretch BKS 0 1 off on BLACK STRETCH MODE Table 121Connection of output of QSS amplifier FMI 0 1 MODE output connected to QSSO output output connected to sound PLL circuit Table 126 Ratio pre- and overshoot RPO1 0 0 1 1 RPO0 0 1 0 1 RATIO PRE-/OVERSHOOT 1:1 1 : 1.25 1 : 1.5 1 : 1.8 2000 Jun 22 75 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Explanation output control data TV-processor Table 127 Power-on-reset POR 0 1 normal power-down MODE TDA955X/6X/8X PS/N1 series Table 133 Output vertical guard NDF 0 1 OK failure VERTICAL OUTPUT STAGE Table 134 Field frequency indication FSI 0 1 50 Hz 60 Hz FREQUENCY Table 128 Output video identification IFI 0 1 VIDEO SIGNAL no video signal identified video signal identified Table 135 Condition vertical divider IVW 0 1 STANDARD VIDEO SIGNAL no standard video signal standard video signal (525 or 625 lines) Table 129 IF-PLL lock indication LOCK 0 1 not locked locked INDICATION Table 136 Indication output black level in/out window WBC 0 1 CONDITION black current stabilisation outside window black current stabilisation inside window Table 130 Phase 1 (1) lock indication SL 0 1 not locked locked INDICATION Table 137 Indication output black level HBC 0 1 CONDITION black current stabilisation below window black current stabilisation above window Table 131 Colour decoder mode, note 1 CD3 CD2 CD1 CD0 0 0 0 0 0 0 0 0 1 1 Note 1. The values for the various frequencies can be found in the note of table 62. Table 132 X-ray protection XPR 0 1 OVERVOLTAGE no overvoltage detected overvoltage detected 76 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 0 STANDARD no colour standard identified NTSC with freq. A PAL with freq. A NTSC with freq. B PAL with freq. B NTSC with freq. C PAL with freq. C NTSC with freq. D PAL with freq. D SECAM Table 138 Condition black current loop BCF 0 1 CONDITION black current loop is stabilised black current loop is not stabilised Table 139 Indication RGB-2 input condition IN2 0 1 no yes RGB INSERTION Table 140 Supply voltage indication SUP 0 1 CONDITION supply voltage (8 Volt) not present supply voltage (8 Volt) present 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Table 141 Indication tuner AGC AGC 0 1 CONDITION tuner gain control active no gain control of tuner TDA955X/6X/8X PS/N1 series Table 145 Indication FM-PLL in/out lock FML 0 1 FM-PLL locked CONDITION FM-PLL out of lock Table 142 Version indication QSS 0 1 IC VERSION version with intercarrier mono sound circuit version with QSS-IF circuit Table 146 Signal-to-Noise ratio SN1 0 0 1 1 CONDITION SN0 0 1 0 1 CONDITION S/N 24 dB S/N 24 dB and 27 dB S/N 27 dB and 31 dB S/N 31 dB Table 143 AFC output AFA 0 0 1 1 AFB 0 1 0 1 outside window; RF too low outside window; RF too high in window; below reference in window; above reference Table 144 Indication FM-PLL in/out window FMW 0 1 CONDITION FM-PLL in window FM-PLL out of window 2000 Jun 22 77 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 2000 Jun 22 78 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP VDD VI VO IO IIOK Tstg Tamb Tsol Tj Ves PARAMETER supply voltage supply voltage (all digital supplies) digital inputs digital outputs output current (each output) DC input or output diode current storage temperature operating ambient temperature soldering temperature operating junction temperature electrostatic handling for 5 s note 1 note 1 TDA955X/6X/8X PS/N1 series CONDITIONS - MIN. 9 -0.5 -0.5 -0.5 - - -25 0 - - MAX. V V 5.0 UNIT VDD+ 0.5 V VDD+ 0.5 V 10 20 +150 70 260 150 +2000 +300 mA mA C C C C V V HBM; all pins; notes 2 and 3 -2000 MM; all pins; notes 2 and 4 -300 Notes 1. This maximum value has an absolute maximum of 5.5 V independent of VDD. 2. All pins are protected against ESD by means of internal clamping diodes. 3. Human Body Model (HBM): R = 1.5 k; C = 100 pF. 4. Machine Model (MM): R = 0 ; C = 200 pF. THERMAL CHARACTERISTICS SYMBOL Rth j-a PARAMETER thermal resistance from junction to ambient in free air 44 VALUE K/W UNIT QUALITY SPECIFICATION In accordance with "SNW-FQ-611E". Latch-up At an ambient temperature of 70 C all pins meet the following specification: * Itrigger 100 mA or 1.5VDD(max) * Itrigger -100 mA or -0.5VDD(max). 2000 Jun 22 79 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series CHARACTERISTICS OF MICRO-COMPUTER AND TEXT DECODER VDD = 3.3 V 10%; VSS = 0 V; Tamb = -20 to +70 C; unless otherwise specified NUMBER Supplies VM.1.1 VM.1.2 VM.1.3 VM.1.4 Digital inputs RESET PARAMETER CONDITIONS MIN. TYP. MAX. UNIT supply voltage (VDDA/P/C) periphery supply current (IDDP) core supply current (IDDC) analog supply current (IDDA) note 1 3.0 1 - - 3.3 - 15 45 3.6 - tbf tbf V mA mA mA I.1.1 I.1.2 I.1.3 I.1.4 I.1.5 I.1.6 low level input voltage high level input voltage hysteresis of Schmitt Trigger input input leakage current equivalent pull down resistance capacitance of input pin VI = 0 V = VDD - 2.0 0.4 - - - - - - - 33 - 0.8 5.5 0.7 1 - 10 V V V A k pF Digital input/outputs P1.0 TO P1.3, P2.0 TO P2.6 AND P3.0 TO P3.3 IO.1.1 IO.1.2 IO.1.3 IO.1.4 IO.1.5 IO.1.6 IO.1.7 IO.1.8 IO.1.9 IO.1.10 low level input voltage high level input voltage hysteresis of Schmitt Trigger input low level output voltage high level output voltage high level output voltage output rise time (push-pull only) 10% to 90% output fall time 10% to 90% load capacitance capacitance of input pin IOL = 4 mA open drain IOH = 4 mA load 100 pF load 100pF - 2.0 0.4 - - 2.4 - - - - - - - - - - 16 14 - - 0.8 5.5 0.7 0.4 5.5 - - - 100 10 V V V V V V ns ns pF pF 2000 Jun 22 80 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER P0.5 AND P0.6 IO.2.1 IO.2.2 IO.2.3 IO.2.4 IO.2.5 IO.2.6 IO.2.7 IO.2.8 IO.2.9 IO.2.10 P1.6 AND P1.7 IO.3.1 IO.3.2 IO.3.3 IO.3.4 IO.3.5 IO.3.6 IO.3.7 IO.3.8 low level input voltage (VIL) high level input voltage (VIH) hysteresis of Schmitt-trigger input low level output voltage high level output voltage output fall time (VIH to VIL for CL) bus load capacitance capacitance of IO pin sink current 8mA open drain low level input voltage high level input voltage hysteresis of Schmitt Trigger input low level output voltage high level output voltage high level output voltage output rise time (push-pull only) 10% to 90% output fall time 10% to 90% load capacitance capacitance of input pin IOL = 8mA open drain IOH = 8mA load 100 pF load 100pF PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - MIN. - - - - - - TYP. MAX. UNIT 0.8 5.5 0.7 0.4 5.5 - - - 100 10 V V V V V V ns ns pF pF 2.0 0.4 - - 2.4 - - - - - 3.0 0.2 0 - 20+0.1x CL 10 - 16 14 - - - - - - - - - - 1.5 5.5 - 0.4 5.5 250 400 10 V V V V V ns pF pF Crystal oscillator OSCIN; NOTE 2 resonator frequency input capacitance (Ci) output capacitance (Co) Cx1 = Cx2 Ri (crystal) - - - 12 - 12 4.0 5.0 - - - - - 56 100 MHz pF pF pF X.1.1 X.1.2 X.1.3 X.1.4 X.1.5 Note 1. Peripheral current is dependent on external components and voltage levels on I/Os 2. The simplified circuit diagram of the oscillator is given in Fig.29. A suitable crystal for this oscillator is the Saronix type 9922 520 00169. The nominal tuning of the crystal is important to obtain a symmetrical catching range for the PLL in the colour decoder. This tuning can be adapted by means of the values of the capacitors Cx1 and Cx2 in Fig.29. Good results were obtained with capacitor values of 39 pF, however, for a new application the optimum value should be determined by checking the symmetry of the catching range of the colour decoder. 2000 Jun 22 81 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller CHARACTERISTICS OF TV-PROCESSORS VP = 5 V; Tamb = 25 C; unless otherwise specified. NUMBER Supplies MAIN SUPPLY; NOTE 1 V.1.1 V.1.2 V.1.4 IF circuit VISION IF AMPLIFIER INPUTS input sensitivity (RMS value) M.1.1 M.1.2 M.1.3 M.1.4 M.1.5 M.1.6 M.1.7 input resistance (differential) input capacitance (differential) gain control range maximum input signal (RMS value) note 2 fi = 38.90 MHz fi = 45.75 MHz fi = 58.75 MHz note 3 note 3 supply voltage total supply current total power dissipation PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT 7.2 - - 8.0 tbf tbf 8.4 - - V mA mW - - - - - 64 150 35 35 35 2 3 - - 100 100 100 - - - - V V V k pF dB mV PLL DEMODULATOR; NOTES 4 AND 5 M.2.1 M.2.2 M.2.3 Free-running frequency of VCO Catching range PLL delay time of identification PLL not locked, deviation from nominal setting without SAW filter via LOCK bit -500 - - - - 1.9 - - - 1.0 - at -3 dB note 10 notes 10 and 6 6 - - - 1 - 4.7 2.0 2.0 4.5 0 50 - - 9 2 - +500 - 20 - - 2.1 - 15 - - 5 - 5 5 kHz MHz ms VIDEO AMPLIFIER OUTPUT; NOTES 7 AND 8 M.3.1 M.3.2 M.3.3 M.3.4 M.3.5 M.3.6 M.3.7 M.3.8 M.3.9 M.3.10 M.3.11 top sync level white level difference in amplitude between negative and positive modulation video output impedance internal bias current of NPN emitter follower output transistor maximum source current bandwidth of demodulated output signal differential gain differential phase zero signal output level negative modulation; note 9 positive modulation; note 9 negative modulation positive modulation V V V V % mA mA MHz % deg 2000 Jun 22 82 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - - note 12 note 12 notes 6 and 13 Vo = 0.92 or 1.1 MHz Vo = 2.66 or 3.3 MHz Vo = 0.92 or 1.1 MHz Vo = 2.66 or 3.3 MHz notes 6 and 14 weighted unweighted - - MIN. - TYP. MAX. UNIT VIDEO AMPLIFIER (CONTINUED) M.3.12 M.3.13 M.3.14 M.3.15 video non-linearity white spot clamp level noise inverter clamping level noise inverter insertion level (identical to black level) intermodulation M.3.16 M.3.17 M.3.18 M.3.19 signal-to-noise ratio M.3.20 M.3.21 M.3.22 M.3.23 residual carrier signal yellow blue note 11 5 - - - % V V V 5.3 1.7 2.8 60 60 56 60 56 49 - - 66 66 62 66 60 53 5.5 2.5 - - - - - - - - dB dB dB dB dB dB mV mV note 6 residual 2nd harmonic of carrier note 6 signal IF AND TUNER AGC; NOTE 15 Timing of IF-AGC M.4.1 M.4.2 M.4.3 M.4.4 modulated video interference response time to IF input signal amplitude increase of 52 dB response to an IF input signal amplitude decrease of 52 dB 30% AM for 1 mV to 100 mV; - 0 to 200 Hz (system B/G) positive and negative modulation negative modulation positive modulation - - - - 40 - 2 50 100 10 - - - 0.8 - % ms ms ms Tuner take-over adjustment (via M.5.1 M.5.2 I2C-bus) 0.4 80 mV mV minimum starting level for tuner take-over (RMS value) maximum starting level for tuner take-over (RMS value) Tuner control output M.6.1 M.6.2 M.6.3 M.6.4 M.6.5 maximum tuner AGC output voltage output saturation voltage maximum tuner AGC output swing leakage current RF AGC input signal variation for complete tuner control maximum tuner gain; note 3 minimum tuner gain; IO = 2 mA - - 5 - 0.5 - - - - 2 8 300 - 1 4 V mV mA A dB 2000 Jun 22 83 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - - - MIN. TYP. - - - MAX. UNIT AFC OUTPUT (VIA I2C-BUS); NOTE 16 M.7.1 M.7.2 M.7.3 AFC resolution window sensitivity window sensitivity in large window mode 2 125 275 bits kHz kHz VIDEO IDENTIFICATION OUTPUT (VIA IFI BIT IN OUTPUT BYTE 00) M.8.1 delay time of identification after the AGC has stabilized on a new transmitter - - 10 ms 2000 Jun 22 84 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER QSS Sound IF circuit SOUND IF AMPLIFIER input sensitivity (RMS value) Q.1.1 Q.1.2 maximum input signal Q.1.3 Q.1.4 Q.1.5 Q.1.6 Q.1.7 Q.1.8 input resistance (differential) input capacitance (differential) gain control range crosstalk attenuation between SIF and VIF input (RMS value) FM mode AM mode note 3 note 3 FM mode (-3 dB) AM mode (-3 dB) PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT - - 50 80 - - 64 50 30 60 70 140 2 3 - - 70 100 - - - - - - V V mV mV k pF dB dB SOUND IF INTERCARRIER OUTPUT; WITH AM = 0 Q.2.1 Q.2.2 Q.2.3 Q.2.4 Q.2.5 Q.2.6 Q.2.7 Q.2.8 Q.2.9 Q.2.10 Q.2.11 Q.2.12 Q.2.13 Q.2.14 output signal amplitude (RMS value) bandwidth (-3 dB) residual IF sound carrier (RMS value) output resistance DC output voltage internal bias current of emitter follower maximum AC and DC sink current maximum AC and DC source current weighted S/N ratio (SC1/SC2). black picture Ratio of PC/SC1 at vision IF white picture input of 40 dB or higher, note 18 6 kHz sinewave (black-to-white modulation) 250 kHz sine wave (black-to-white modulation) sound carrier subharmonics (f=2.75 MHz 3 kHz) sound carrier subharmonics (f=2.87 MHz 3 kHz) SC-1; sound carrier 2 off 75 7.5 - - - - - - 53/48 52/47 44/42 44/25 45/44 46/45 100 9 2 tbf tbf tbf tbf tbf 58/55 55/53 48/46 48/30 51/50 52/51 125 - - - - - - - - - - - - - mV MHz mV V mA mA mA dB dB dB dB dB dB 2000 Jun 22 85 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT AM SOUND OUTPUT; DEPENDING ON SETTING OF CMB0/CMB1 AND AM BITS Q.3.1 Q.3.2 Q.3.21 Q.3.3 Q.3.4 Q.3.5 Q.3.6 AF output signal amplitude (RMS value) total harmonic distortion total harmonic distortion AF bandwidth weighted signal-to-noise ratio DC output voltage power supply ripple rejection 54% modulation 54% modulation 80% modulation -3 dB 400 - - 100 47 - - 500 0.5 tbf 125 53 tbf tbf 600 1.0 5.0 - - - - mV % % kHz dB V dB FM demodulator and audio amplifier FM-PLL DEMODULATOR; NOTE 19 G.1.1 IF intercarrier level at IF video output (RMS value) for lock-in of PLL gain control range AGC amplifier catching range PLL maximum phase detector output current VCO steepness fFM/VC (K0) phase detector steepness IC/VFM (KD) AM rejection note 21 note 20 - - tbf mV G.1.2 G.1.3 G.1.4 G.1.5 G.1.6 G.1.7 26 - - - - 40 - note 3 note 3 - - - - - - - maximum volume - 30 225 100 3.3 9 46 - - - - - - 2 - 5 - - - - - - dB kHz A MHz/V A/rad dB EXTERNAL SOUND IF INPUT (SNDIF, WHEN SELECTED) G.1.8 G.1.9 G.1.10 input limiting for lock-in of PLL (RMS value) input resistance input capacitance 1 8.5 - 500 15 3 mV k pF DE-EMPHASIS OUTPUT; NOTE 23 G.2.1 G.2.2 G.2.3 output signal amplitude (RMS value) output resistance DC output voltage note 20 mV k V AUDIO INPUT VIA DEEMPHASIS OUTPUT; NOTE 23 G.2.4 G.2.5 G.2.6 input signal amplitude (RMS value) input resistance voltage gain between input and output 500 15 9 mV k dB 2000 Jun 22 86 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER Audio Amplifier AUDIO OUTPUT OR VOLUME CONTROLLED AM-OUT A.1.1 A.1.2 A.1.3 A.1.4 A.1.5 A.1.6 A.1.7 A.1.8 A.1.9 A.1.10 A.1.11 A.1.12 controlled output signal amplitude (RMS value) output resistance DC output voltage total harmonic distortion total harmonic distortion power supply rejection internal signal-to-noise ratio external signal-to-noise ratio output level variation with temperature control range suppression of output signal when mute is active DC shift of the output when mute is active note 24 note 25 note 6 note 6 + 26 note 6 + 26 note 6 + 27 see also Fig.30 PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT -6 dB; nominal audio input signal 500 - - - - - - - - - - - 700 500 tbf - - tbf 60 80 - 80 80 10 900 - - 0.5 tbf - - - tbf - - 50 mV V % % dB dB dB dB dB dB mV EXTERNAL AUDIO INPUT A.2.1 A.2.2 A.2.3 A.2.4 input signal amplitude (RMS value) input resistance voltage gain between input and output crosstalk between internal and external audio signals maximum volume - - - 60 500 25 9 - 2000 - - - mV k dB dB AUTOMATIC VOLUME LEVELLING; NOTE 28 A.3.1 A.3.2 A.3.3 A.3.4 A.3.5 A.3.6 gain at maximum boost gain at minimum boost charge (attack) current discharge (decay) current control voltage at maximum boost control voltage at minimum boost - - - - - - 6 -14 1 200 tbf tbf - - - - - - dB dB mA nA V V 2000 Jun 22 87 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT CVBS, Y/C and RGB/YUV INPUTS CVBS-Y/C SWITCH S.1.1 S.1.2 S.1.3 S.1.4 S.1.5 CVBS or Y input voltage (peak-to-peak value) CVBS or Y input current suppression of non-selected CVBS input signal notes 6 and 30 note 29 - - 50 - - note 32 - 1.0 4 - 0.3 50 1.4 - - 1.0 - 0.8 V A dB V k chrominance input voltage (burst note 3 and 31 amplitude) chrominance input impedance EXTERNAL RGB / YUV (YPBPR) INPUT S.2.1 RGB input signal amplitude for an output signal of 1 V (black-to-white) (peak-to-peak value) RGB input signal amplitude before clipping occurs (peak-to-peak value) Y input signal amplitude (peak-to-peak value) U/PB input signal amplitude (peak-to-peak value) V/PR input signal amplitude (peak-to-peak value) difference between black level of internal and external signals at the outputs input currents delay difference for the three channels no clamping; note 3 note 6 0.7 V S.2.2 note 6 1.0 - - V S.2.3 S.2.4 S.2.5 S.2.6 input signal amplitude for an - output signal of 2 V (black-to-white); when - activated via the YUV1/YUV0 bits; note 33 - - 1.4/1.0 -1.33/ +0.7 -1.05/ +0.7 - 2.0 2.0 1.5 20 V V V mV S.2.7 S.2.8 - - 0.1 0 1 20 A ns FAST INSERTION S.3.1 S.3.2 S.3.3 S.3.4 S.3.5 maximum input pulse delay time from RGB in to RGB out input voltage no data insertion data insertion insertion data insertion; note 6 - 0.9 - - - - - - - - 0.4 - 3.0 tbf tbf V V V ns ns delay difference between data insertion; note 6 insertion to RGB out and RGB in to RGB out input current suppression of internal RGB signals suppression of external RGB signals notes 6 and 30; insertion; fi = 0 to 5 MHz S.3.6 S.3.7 S.3.8 - - - 55 55 0.2 - - mA dB dB notes 6 and 30; no insertion; - fi = 0 to 5 MHz 88 2000 Jun 22 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT Chrominance and Luminance filters CHROMINANCE TRAP CIRCUIT; NOTE 34 F.1.1 F.1.2 F.1.3 F.1.4 F.1.5 trap frequency Bandwidth at fSC = 3.58 MHz Bandwidth at fSC = 4.43 MHz colour subcarrier rejection trap frequency during SECAM reception -3 dB -3 dB - - - 24 - fosc 2.8 3.4 26 4.3 - - - - - MHz MHz MHz dB MHz CHROMINANCE BANDPASS CIRCUIT F.2.1 F.2.2 F.2.3 centre frequency (CB = 0) centre frequency (CB = 1) bandpass quality factor - - - 4.26 241 - -160 8 fosc 1.1xfosc 3 - - - 4.31 295 - +160 - MHz kHz MHz MHz CLOCHE FILTER F.3.1 F.3.2 Y DELAY LINE F.4.1 F.4.2 F.4.3 delay time tuning range delay time bandwidth of internal delay line note 6 8 steps note 6 480 - - ns ns MHz centre frequency Bandwidth 4.29 268 2000 Jun 22 89 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT Picture Improvement Features PEAKING CONTROL; NOTE 35 P.1.1 P.1.2 P.1.3 P.1.4 P.1.5 P.1.6 P.1.7 P.1.8 P.1.9 CORING STAGE; NOTE 37 P.1.10 coring range - 15 -1 -1 6 - - - 10 - 27 1 3 10 - - - IRE Ratio negative/positive overshoot; note 36 peaking control curve peaking centre frequency 63 steps setting PF1/PF0 = 0/0 setting PF1/PF0 = 0/1 setting PF1/PF0 = 1/0 width of preshoot or overshoot peaking signal compression threshold overshoot at maximum peaking positive negative note 3 - - - - - 160 50 45 80 1.8 - - - - - ns IRE % % see Fig.31 - - - 2.7 3.1 3.5 - - - MHz MHz MHz BLACK LEVEL STRETCHER; NOTE 38 P.2.1 P.2.2 P.2.3 P.2.4 Maximum black level shift level shift at 100% peak white level shift at 50% peak white level shift at 15% peak white 21 0 - 8 IRE IRE IRE IRE DYNAMIC SKIN TONE (FLESH) CONTROL; NOTE 39 P.4.1 P.4.2 control angle correction range (angle) 123 45 deg deg BLUE STRETCH; NOTE 41 P.7.1 decrease of small signal gain for BLS = 1 the red and green channel 14 % 2000 Jun 22 90 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT Horizontal and vertical synchronization and drive circuits SYNC VIDEO INPUT H.1.1 H.1.2 H.1.3 sync pulse amplitude slicing level for horizontal sync slicing level for vertical sync note 3 note 42 note 42 50 - - - - - - 300 50 35 350 - - - 2 0.5 80 mV % % HORIZONTAL OSCILLATOR H.2.1 H.2.2 H.2.3 H.2.4 free running frequency spread on free running frequency frequency variation with respect VP = 8.0 V 10%; note 6 to the supply voltage frequency variation with temperature Tamb = 0 to 70 C; note 6 15625 - 0.2 - Hz % % Hz FIRST CONTROL LOOP; NOTE 43 H.3.1 H.3.2 H.3.3 holding range PLL catching range PLL signal-to-noise ratio of the video input signal at which the time constant is switched hysteresis at the switching point note 6 - 0.6 - 0.9 0.9 24 1.2 - - kHz kHz dB H.3.4 - - - 3 - - - dB s/s s SECOND CONTROL LOOP H.4.1 H.4.2 control sensitivity control range from start of horizontal output to flyback at nominal shift position horizontal shift range control sensitivity for dynamic compensation Voltage to switch-on the `flash' protection Input current during protection control range of the parallelogram correction control range of the bow correction note 45 note 45 note 44 63 steps 150 19 H.4.3 H.4.4 H.4.5 H.4.6 H.4.7 H.4.8 2 - 6.0 - - - - 7.6 - - 0.5 0.5 - - - 1 - - s s/V V mA s s 2000 Jun 22 91 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - MIN. - - - TYP. MAX. UNIT HORIZONTAL OUTPUT; NOTE 46 H.5.1 H.5.2 H.5.3 H.5.4 H.5.5 H.5.6 LOW level output voltage maximum allowed output current maximum allowed output voltage duty factor switch-on time of horizontal drive pulse switch-off time of horizontal drive pulse VOUT = LOW (TON) IO = 10 mA 0.3 - VP - - - V mA V % ms ms 10 - - - - 55 1175 43 FLYBACK PULSE INPUT AND SANDCASTLE OUTPUT H.6.1 H.6.2 H.6.3 H.6.4 H.6.5 H.6.6 delay of start of burst key to start of sync required input current during flyback pulse output voltage clamped input voltage during flyback pulse width burst key pulse vertical blanking, note 47 note 3 during burst key during blanking 100 4.8 2.3 2.6 3.3 - 4.6 - 5.3 2.5 3.0 3.5 14/9.5 4.8 300 5.8 2.7 3.4 3.7 - 5.0 A V V V s lines s VERTICAL OSCILLATOR; NOTE 48 H.7.1 H.7.2 H.7.3 H.7.4 free running frequency locking range divider value not locked locking range - 45 - 434/488 50/60 - 625/525 - - - 722 Hz lines lines/ frame 64.5/72 Hz VERTICAL RAMP GENERATOR H.8.1 H.8.2 H.8.3 H.8.4 H.8.5 H.8.6 sawtooth amplitude (peak-to-peak value) discharge current charge current set by external resistor vertical slope charge current increase LOW level of ramp note 49 63 steps; see Fig. 51 f = 60 Hz VS = 1FH; C = 100 nF; R = 39 k - - - -20 - - VA = 1FH - - 0 3.0 1 16 - 19 2.3 - - - +20 - - - - 4.0 V mA A % % V VERTICAL DRIVE OUTPUTS H.9.1 H.9.2 H.9.3 differential output current (peak-to-peak value) common mode current output voltage range 0.95 400 - mA A V 2000 Jun 22 92 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. - - TYP. MAX. UNIT EHT TRACKING/OVERVOLTAGE PROTECTION H.10.1 H.10.2 H.10.3 H.10.4 H.10.5 H.10.6 DE-INTERLACE H.11.1 first field delay - 63 steps; see Fig. 54 100 0 1.0 0 0.5H - - - - - - - - - - - - - 65 700 5.0 1200 % A V A % A % A % A % A input voltage scan modulation range vertical sensitivity EW sensitivity EW equivalent output current overvoltage detection level note 44 when switched-on 1.2 -5 - - +100 - 2.8 +5 - - -100 - V % %/V %/V A V 6.3 -6.3 - 3.9 EW WIDTH; NOTE 50 H.12.1 H.12.2 H.12.3 H.12.4 control range equivalent output current EW output voltage range EW output current range EW PARABOLA/WIDTH H.13.1 H.13.2 control range equivalent output current 63 steps; see Fig. 55 0 23 450 EW=3FH; CP=11H; TC=1FH 0 -46 EW UPPER/LOWER CORNER/PARABOLA H.14.1 H.14.2 control range equivalent output current 63 steps; see Fig. 56 +17 +76 PW=3FH; EW=3FH; TC=1FH -207 63 steps; see Fig. 57 -5 EW TRAPEZIUM H.15.1 H.15.2 control range equivalent output current +5 +100 EW=1FH; CP=11H; PW=1FH -100 63 steps; see Fig. 50 SC = 0EH 80 760 VERTICAL AMPLITUDE H.16.1 H.16.2 control range equivalent differential vertical drive output current (peak-to-peak value) 120 1140 VERTICAL SHIFT H.17.1 H.17.2 control range equivalent differential vertical drive output current (peak-to-peak value) 63 steps; see Fig. 52 -5 -50 - - +5 +50 % A S-CORRECTION H.18.1 control range 63 steps; see Fig. 53 -10 0.75 - - - 1.05 25 % VERTICAL ZOOM MODE (OUTPUT CURRENT VARIATION WITH RESPECT TO NOMINAL SCAN); NOTE 51 H.19.1 H.19.2 vertical expand factor output current limiting and RGB blanking 1.38 - 2000 Jun 22 93 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT Colour demodulation part CHROMINANCE AMPLIFIER D.1.1 D.1.2 ACC control range change in amplitude of the output signals over the ACC range threshold colour killer ON hysteresis colour killer OFF strong signal conditions; S/N 40 dB; note 6 noisy input signals; note 6 note 52 26 - - - - 2 dB dB D.1.3 D.1.4 D.1.5 -30 - - - - +3 +1 - - - - dB dB dB ACL CIRCUIT; NOTE 53 D.2.1 chrominance burst ratio at which the ACL starts to operate 3.0 REFERENCE PART Phase-locked loop D.3.1 D.3.2 catching range phase shift for a 400 Hz deviation of the oscillator frequency note 6 500 - tbf - - 2 Hz deg HUE CONTROL D.5.1 D.5.2 D.5.3 hue control range hue variation for 10% VP hue variation with temperature 63 steps; see Fig.32 note 6 Tamb = 0 to 70 C; note 6 35 - - 40 0 0 - - - deg deg deg DEMODULATORS General D.6.3 D.6.5 spread of signal amplitude ratio between standards bandwidth of demodulators note 6 -3 dB; note 54 -1 - 1.60 note 6 note 6 note 6 - - - - 650 +1 - 1.96 - 0.1 5 %/K dB deg dB kHz PAL/NTSC demodulator D.6.6 D.6.12 D.6.13 D.6.14 gain between both demodulators G(B-Y) and G(R-Y) change of output signal amplitude with temperature change of output signal amplitude with supply voltage phase error in the demodulated signals 1.78 0.1 - - 2000 Jun 22 94 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - MIN. - TYP. MAX. UNIT SECAM demodulator D.7.1 D.7.2 D.7.3 D.7.4 D.7.5 black level off-set pole frequency of deemphasis ratio pole and zero frequency non linearity calibration voltage 7 93 - 3 tbf % V kHz kHz 77 - - tbf -0.1 85 3 - 2.3 - Base-band delay line D.8.1 variation of output signal for adjacent time samples at constant input signals residual clock signal (peak-to-peak value) delay of delayed signal delay of non-delayed signal difference in output amplitude with delay on or off 0.1 dB D.8.2 D.8.3 D.8.4 D.8.5 - 63.94 40 - - 64.0 60 - 5 64.06 80 5 mV s ns % COLOUR DIFFERENCE MATRICES (IN CONTROL CIRCUIT) PAL/SECAM mode; (R-Y) and (B-Y) not affected D.9.1 D.9.2 ratio of demodulated signals (G-Y)/(R-Y) ratio of demodulated signals (G-Y)/(B-Y) - - -0.51 10% -0.19 25% - - NTSC mode; the matrix results in the following signals (nominal hue setting) MUS-bit = 0 D.9.6 D.9.7 D.9.8 MUS-bit = 1 D.9.9 D.9.10 D.9.11 (B-Y) signal: 2.20/-1 (R-Y) signal: 1.53/99 (G-Y) signal: 0.70/223 2.20UR - 0.04VR -0.24UR + 1.51VR -0.51UR - 0.48VR CMB1/CMB0 = 01 CMB1/CMB0 = 01 CMB1/CMB0 = 01 CMB1/CMB0 = 10 CMB1/CMB0 = 11 0.2 tbf - 4.5 3.58/4.43 0.25 2.3 - - 0.3 tbf 0.8 - MHz V V V V (B-Y) signal: 2.03/0 (R-Y) signal: 1.59/95 (G-Y) signal: 0.61/240 2.03UR -0.14UR + 1.58VR -0.31UR - 0.53VR REFERENCE SIGNAL OUTPUT/SWITCH OUTPUT; NOTE 55 D.10.1 D.10.2 D.10.3 D.10.4 D.10.5 reference frequency output signal amplitude (peak-to-peak value) output level (mid position) output level LOW output level HIGH 2000 Jun 22 95 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER Control part SATURATION CONTROL; NOTE 32 C.1.1 saturation control range 63 steps; see Fig.33 PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS MIN. TYP. MAX. UNIT 52 - - - 20 - - - 0.5 dB CONTRAST CONTROL; NOTE 32 C.2.1 C.2.2 contrast control range tracking between the three channels over a control range of 10 dB contrast reduction 63 steps; see Fig.34 dB dB C.2.6 - 63 steps; see Fig.35 - 6 0.7 2.0 - - tbf dB BRIGHTNESS CONTROL C.3.1 brightness control range V RGB AMPLIFIERS C.4.1 output signal amplitude (peak-to-peak value) at nominal luminance input tbf signal, nominal settings for contrast, white-point adjustment and cathode drive level(CL3-CL0 = 0111) note 56 - - V C.4.2 C.4.3 maximum signal amplitude (black-to-white) tbf tbf - - V V input signal amplitude note 56 (CVBS/Y-input) at which the soft clipping is activated output signal amplitude for the `red' channel (peak-to-peak value) nominal black level voltage black level voltage C.4.4 at nominal settings for tbf contrast and saturation control and no luminance signal to the input (R-Y, PAL) - when black level stabilisation - is switched-off (via AKB bit) 1.8 3.5 7.8 - - difference with black level, note 56 - - - - - 96 start of blanking; note 58 end of blanking; note 58 2.1 tbf V C.4.5 C.4.6 C.4.61 C.4.71 C.4.72 C.4.8 C.4.81 C.4.9 C.4.10 C.4.11 C.4.12 C.4.13 2000 Jun 22 2.5 2.5 2.5 - - 1 tbf -0.5 -0.1 0.25 0.5 3 - - 3.2 5.9 10.2 - - - - - - - V V V s s V V V V V V dB black level voltage control range AVG bit active; note 57 timing of video blanking with respect to mid sync (HBL = 1) control range of the black-current stabilisation RGB output level when RGBL=1 blanking level level during leakage measurement level during `low' measuring pulse level during `high' measuring pulse adjustment range of the cathode note 56 drive level Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER C.4.131 PARAMETER gain control range to compensate spreads in picture tube characteristics for the 2-point black -current stabilization system variation of black level with temperature note 6 TDA955X/6X/8X PS/N1 series CONDITIONS - MIN. TYP. 6 - MAX. UNIT dB C.4.14 C.4.141 C.4.15 - tbf 1.0 160 - tbf mV/K mV black level off-set adjustment on 63 steps the Red and Green channel relative variation in black level between the three channels during variations of supply voltage (10%) saturation (50 dB) contrast (20 dB) brightness (0.5 V) temperature (range 40 C) signal-to-noise ratio of the output RGB input; note 59 signals CVBS input; note 59 residual voltage at the RGB outputs (peak-to-peak value) bandwidth of output signals at fosc RGB input; at -3 dB CVBS input; at -3 dB; fosc = 3.58 MHz CVBS input; at -3 dB; fosc = 4.43 MHz S-VHS input; at -3 dB I2C-bus setting for nominal gain adjustment range of the relative R, G and B drive levels HEX code AKB = 0 AKB = 1 note 6 C.4.16 C.4.17 C.4.18 C.4.19 C.4.20 C.4.21 C.4.22 C.4.23 C.4.24 C.4.25 C.4.26 C.4.27 C.4.28 nominal controls nominal contrast nominal saturation nominal controls - - - - - 60 50 - tbf - - 5 - - - - - - - - - - - - - - - - 15 2.8 3.4 - 20H 1 8 40 75 tbf 200 tbf 0.1 tbf tbf tbf tbf tbf - - 15 15 - - - - - mV mV mV mV mV dB dB mV mV MHz MHz MHz MHz at 2fosc plus higher harmonics - WHITE-POINT ADJUSTMENT C.5.1 C.5.2 C.5.21 +2.2/-3.2 - - - - - - - - - dB dB A A A mA k mA 2-POINT BLACK-CURRENT STABILIZATION, NOTES 60 C.6.1 C.6.2 C.6.3 C.6.4 C.6.5 C.6.5 C.6.7 minimum input current to activate the guard circuit amplitude of `low' reference current amplitude of `high' reference current acceptable leakage current maximum current during scan input impedance during measuring pulses during scan note 61 - - - 2000 Jun 22 97 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller NUMBER BEAM CURRENT LIMITING C.7.1 C.7.2 C.7.3 C.7.4 C.7.5 C.7.6 contrast reduction starting voltage voltage difference for full contrast reduction brightness reduction starting voltage voltage difference for full brightness reduction internal bias voltage maximum allowable current PARAMETER TDA955X/6X/8X PS/N1 series CONDITIONS - - - - - - MIN. TYP. - - - - - - MAX. UNIT 2.8 1.8 1.7 0.9 3.3 tbf V V V V V mA FIXED BEAM CURRENT SWITCH-OFF; NOTE 62 C.8.1 C.8.2 discharge current during switch-off discharge time of picture tube 0.85 - PWL range (15 steps); at max. contrast maximum contrast; note 64, see Fig.47 0.55 1.0 38 - 1.15 - 0.85 mA ms PEAK WHITE LIMITER AND SOFT CLIPPING; NOTES 63 AND 64 C.9.1 CVBS/Y-input signal amplitude at which peak white limiter is activated (black-to-white value) soft clipper gain reduction V C.9.2 Notes - 8 - dB 1. When the 3.3 V supply is present and the -Controller is active a `low-power start-up' mode can be activated. When all sub-address bytes have been sent and the POR and XPR flags have been cleared the horizontal output can be switched-on via the STB-bit (subaddress 24H). In this condition the horizontal drive signal has the nominal TOFF and the TON grows gradually from zero to the nominal value. As soon as the 8 V supply is present the switch-on procedure (e.g. closing of the second loop) is continued. 2. On set AGC. 3. This parameter is not tested during production and is just given as application information for the designer of the television receiver. 4. Loop bandwidth BL = 60 kHz (natural frequency fN = 15 kHz; damping factor d = 2; calculated with top sync level as FPLL input signal level). 5. The IF-PLL demodulator uses an internal VCO (no external LC-circuit required) which is calibrated by means of a digital control circuit which uses the clock frequency of the -Controller as a reference. The required IF frequency for the various standards is set via the IFA-IFC bits in subaddress 27H. When the system is locked the resulting IF frequency is very accurate with a deviation from the nominal value of less than 25 kHz. 6. This parameter is not tested during production but is guaranteed by the design and qualified by means of matrix batches which are made in the pilot production period. 7. Measured at 10 mV (RMS) top sync input signal. 8. Via this pin both the demodulated IF signal and the selected CVBS (or Y+C) signal can be supplied to the output. The selection between both signals is realised by means of the SVO bit in subaddress 22H. 9. So called projected zero point, i.e. with switched demodulator. 2000 Jun 22 98 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 10. Measured in accordance with the test line given in Fig.36. For the differential phase test the peak white setting is reduced to 87%. The differential gain is expressed as a percentage of the difference in peak amplitudes between the largest and smallest value relative to the subcarrier amplitude at blanking level. The phase difference is defined as the difference in degrees between the largest and smallest phase angle. 11. This figure is valid for the complete video signal amplitude (peak white-to-black), see Fig.37. 12. The noise inverter is only active in the `strong signal mode' (no noise detected in the incoming signal) 13. The test set-up and input conditions are given in Fig.38. The figures are measured with an input signal of 10 mV RMS. This test can only be carried out in a test set-up in which the test options of the IC can be activated. This because the IF-AGC control input is not available in this IC. 14. Measured at an input signal of 10 mVRMS. The S/N is the ratio of black-to-white amplitude to the black level noise voltage (RMS value). B = 5 MHz. Weighted in accordance with CCIR 567. 15. The time-constant of the IF-AGC is internal and the speed of the AGC can be set via the bits AGC1 and AGC0 in subaddress 28H. The AGC response time is also dependent on the acquisition time of the PLL demodulator. The values given are valid for the `norm' setting (AGC1-AGC0 = 0-1) and when the PLL is in lock. 16. The AFC control voltage is generated by the digital tuning system of the PLL demodulator. This system uses the clock frequency of the -Controller/Teletext decoder as a reference and is therefore very accurate. For this reason no maximum and minimum values are given for the window sensitivity figures (parameters M.7.2 and M.7.3). The tuning information is supplied to the tuning system via the AFA and AFB bits in output byte 02H. The AFC value is valid only when the LOCK-bit is 1. 17. The reference signal for the I-mixer (frequency 42 or 48 MHz) is internally generated. It is also possible to supply an external reference signal to the mixer. This external mode is activated by means of the IFE bit, the signal has to be supplied to the pin which is normally used as the reference signal output of the colour decoder (REFO). 18. The weighted S/N ratio is measured under the following conditions: a) The vision IF modulator must meet the following specifications: Incidental phase modulation for black-to-white jumps less than 0.5 degrees. QSS AF performance, measured with the television-demodulator AMF2 (audio output, weighted S/N ratio) better than 60 dB (deviation 27 kHz) for 6 kHz sine wave black-to-white modulation. Picture-to-sound carrier ratio: PC/SC1 = 13 dB (transmitter). b) The measurements must be carried out with the Siemens SAW filters G3962 for vision IF and G9350 for sound IF. Input level for sound IF 10 mVRMS with 27 kHz deviation. c) The PC/SC ratio at the vision IF input is calculated as the addition of the TV transmitter ratio and the SAW filter PC/SC ratio. This PC/SC ratio is necessary to achieve the S/N(W) values as indicated. 2000 Jun 22 99 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 19. Calculation of the FM-PLL filter can be done approximately by use of the following equations: 1 K0 KD f o = ------ ------------2 C P 1 = ---------------------------------2R K 0 K D C P BL-3dB = f0(1.55 - 2) These equations are only valid under the conditions that 1 and CS >5CP. Definitions: K0 = VCO steepness in rad/V KD = phase detector steepness A/rad R = loop filter resistor CS = series capacitor CP = parallel capacitor f0 = natural frequency of PLL BL-3dB = loop bandwidth for -3dB = damping factor Some examples for these values are given in table 147 20. Modulation frequency: 1 kHz, f = 50 kHz. 21. f = 4.5/5.5 MHz; FM: 70 Hz, 50 kHz deviation; AM: 1.0 kHz, 30% modulation. 22. This figure is independent of the TV standard and valid for a frequency deviation of 25 kHz at a carrier frequency of 4.5 MHz or a deviation of 50 kHz at a carrier frequency of 5.5/6.0/6.5 MHz. 23. The deemphasis pin can also be used as additional audio input. In that case the internal (demodulated FM signal) must be switched off. This can be realised by means of the SM (sound mute) bit. When the vision IF amplifier is switched to positive modulation the signal from the FM demodulator is automatically switched off. The external signal must be switched off when the internal signal is selected. 24. Audio input signal 200 mVRMS. Measured with a bandwidth of 15 kHz and the audio attenuator at -6 dB. 25. Audio input signal 1 VRMS and the volume control setting such that no clipping occurs in the audio output. 26. Unweighted RMS value, audio input signal 500 mVRMS, audio attenuator at -6 dB. 27. Audio attenuator at -20 dB; temperature range 10 to 50 C. 28. In various versions the Automatic Volume Levelling (AVL) function can be activated. The pin to which the external capacitor has to be connected depends on the IC version. For the 90 types the capacitor is connected to the EW output pin. For the 110 types a choice can be made between the AVL function and a sub-carrier output / general purpose switch output. The selection must be made by means of the CMB0 and CMB1 bit in subaddress 22H (see also table G-1 on page G-9). More details about the sub-carrier output are given in the parameters D.10. The Automatic Volume Levelling (AVL) circuit stabilises automatically the audio output signal to a certain level which can be set by means of the volume control. This AVL function prevents big audio output fluctuations due to variation of the modulation depth of the transmitter. The AVL can be switched on and off via the AVL bit in subaddress 29H. The AVL is active over an input voltage range (measured at the deemphasis output) of 150 to 1500 mVRMS. The AVL control curve is given in Fig.39. The control range of +6 dB to -14 dB is valid for input signals with 50% of the maximum frequency deviation. 29. Signal with negative-going sync. Amplitude includes sync pulse amplitude. 30. This parameter is measured at nominal settings of the various controls. 31. Indicated is a signal for a colour bar with 75% saturation (chroma : burst ratio = 2.2 : 1). 2000 Jun 22 100 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 32. The contrast and saturation control is active on the internal signal (YUV) and on the external RGB/YUV input. The Text/OSD input can be controlled on brightness only. Nominal contrast is specified with the DAC in position 20 HEX. Nominal saturation as maximum -10 dB. 33. The YUV/YPBPR input signal amplitudes are based on a colour bar signal with 75/100% saturation. 34. When the decoder is forced to a fixed subcarrier frequency (via the CM-bits) the chroma trap is always switched-on, also when no colour signal is identified. In the automatic mode the chroma trap is switched-off when no colour signal is identified. 35. Valid for a signal amplitude on the Y-input of 0.7 V black-to-white (100 IRE) with a rise time (10% to 90%) of 70 ns and the video switch in the Y/C mode. During production the peaking function is not tested by measuring the overshoots but by measuring the frequency response of the Y output. 36. The ratio between the positive and negative peaks can be varied by means of the bits RPO1 and RPO0 in subaddress 2EH. For ratios which are smaller than 1.8 the positive peak is not affected and the negative peak is reduced. 37. The coring can be activated in the low-light part of the picture. This effectively reduces the noise while having maximum peaking in the bright parts of the picture. The setting the video content at which the coring is active can be adapted by means of the COR1/COR0 bits in subaddress 2DH. 38. For video signals with a black level which deviates from the back-porch blanking level the signal is "stretched" to the blanking level. The amount of correction depends on the IRE value of the signal (see Fig.40). The black level is detected by means of an internal capacitor. The black level stretcher can be switched on and off via the BKS bit in subaddress 2DH. The values given in the specification are valid only when the luminance input signal has an amplitude of 1 Vp-p. 39. The Dynamic Skin Tone Correction circuit is designed such that it corrects (instantaneously and locally) the hue of those colours which are located in the area in the UV plane that matches to skin tones. The correction is dependent on the luminance, saturation and distance to the preferred axis. Because the amount of correction is dependent on the parameters of the incoming YUV signal it is not possible to give exact figures for the correction angle. The correction angle of 45 (22.5) degrees is just given as an indication and is valid for an input signal with a luminance signal amplitude of 75% and a colour saturation of 50%. A graphical representation of the control behaviour is given in Figure 41 on page 112. 40. Stretching is 50% when the average video content has the level which is chosen with these bits. The stretching varies from 100% to 0% over an average video range of 25% to 30%. 41. Via the `blue stretch' (BLS bit) function the colour temperature of the bright scenes (amplitudes which exceed a value of 80% of the nominal amplitude) can be increased. This effect is obtained by decreasing the small signal gain of the red and green channel signals which exceed the 80% level. The effect is illustrated in Figure 42 on page 113. 42. The slicing level is independent of sync pulse amplitude. The given percentage is the distance between the slicing level and the black level (back porch). When the amplitude of the sync pulse exceeds the value of 350 mV the sync separator will slice the sync pulse at a level of 175 mV above top sync. The maximum sync pulse amplitude is 4 Vp-p. The vertical slicing level is dependent on the S/N ratio of the incoming video signal. For a S/N 24 dB the slicing level is 35%, for a S/N 24 dB the slicing level is 60%. With the bit FSL (Forced Slicing Level) the vertical slicing level can be forced to 60%. 43. To obtain a good performance for both weak signal and VCR playback the time constant of the first control loop is switched depending on the input signal condition and the condition of the POC, FOA, FOB and VID bits in subaddress 24H. The circuit contains a noise detector and the time constant is switched to `slow' when too much noise is present in the signal. In the `fast' mode during the vertical retrace time the phase detector current is increased 50% so that phase errors due to head-switching of the VCR are corrected as soon as possible. Switching of the time constant can be automatically or can be set by means of the control bits. The circuit contains a video identification circuit which is independent of the first loop. This identification circuit can be used to close or open the first control loop when a video signal is present or not present on the input. This enables a stable On Screen Display (OSD) when just noise is present at the input. 2000 Jun 22 101 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series To prevent that the horizontal synchronisation is disturbed by anti copy signals like Macrovision the phase detector is gated during the vertical retrace period so that pulses during scan have no effect on the output voltage. The width of the gate pulse is about 22 s. During weak signal conditions (noise detector active) the gating is active during the complete scan period and the width of the gate pulse is reduced to 5.7 s so that the effect of noise is reduced to a minimum. The output current of the phase detector in the various conditions are shown in Table 148. 44. The ICs have 2 protection inputs. The protection on the second phase detector pin is intended to be used as `flash' protection. When this protection is activated the horizontal drive is switched-off immediately and then switched-on again via the slow start procedure. The protection on the EHT input is intended for overvoltage (X-ray) protection. When this protection is activated the horizontal drive is directly switched-off (via the slow stop procedure). The EHT protection input can also be used to switch-off the TV receiver in a correct way when it is switched off via the mains power switch or when the power supply is interrupted by pulling the mains plug. This can be realised by means of a detection circuit which monitors the main supply voltage of the receiver. When this voltage suddenly decreases the EHT protection input must be pulled HIGH and then the horizontal drive is switched off via the slow stop procedure. Whether the EHT capacitor is discharged in the overscan or not during the switch-off period depends on the setting of the OSO bit (subaddress 25H, D4). See also note 62. 45. The control range indicates the maximum phase difference at the top and the bottom of the screen. Compared with the phase position at the centre of the screen the maximum phase difference at the top and the bottom of the screen is 0.5 s for both the parallelogram and the bow correction. 46. During switch-on the horizontal drive starts-up in a soft-start mode. The horizontal drive starts with a very short TON time of the horizontal output transistor, the `off time' of the transistor is identical to the `off time' in normal operation. The starting frequency during switch-on is therefore about 2 times higher than the normal value. The `on time' is slowly increased to the nominal value in a time of about 1175 ms (see Fig.45). The rather slow rise of the TON between 75% and 100% of TON is introduced to obtain a sufficiently slow rise of the EHT for picture tubes with Dynamic Astigmatic Focus (DAF) guns. When the nominal frequency is reached the PLL is closed in such a way that only very small phase corrections are necessary. This ensures a safe operation of the output stage. During switch-off the soft-stop function is active. This is realised by decreasing the TON of the output transistor complimentary to the start-up behaviour. The switch-off time is about 43 ms (see Fig.45). When the `switch off command' is received the soft-stop procedure is started after a delay of about 2 ms. During the switch-off time the EHT capacitor of the picture tube is discharged with a fixed beam current which is forced by the black current loop (see also note 62). The discharge time is about 38 ms. The horizontal output is gated with the flyback pulse so that the horizontal output transistor cannot be switched-on during the flyback time. 47. The vertical blanking pulse in the RGB outputs has a width of 27 or 22 lines (50 or 60 Hz system). The vertical pulse in the sandcastle pulse has a width of 14 or 9.5 lines (50 or 60 Hz system). This to prevent a phase distortion on top of the picture due to a timing modulation of the incoming flyback pulse. 48. The timing pulses for the vertical ramp generator are obtained from the horizontal oscillator via a divider circuit. During TV reception this divider circuit has 3 modes of operation: a) Search mode `large window'. This mode is switched on when the circuit is not synchronized or when a non-standard signal (number of lines per frame outside the range between 311 and 314(50 Hz mode) or between 261 and 264 (60 Hz mode) is received). In the search mode the divider can be triggered between line 244 and line 361 (approximately 45 to 64.5 Hz). 2000 Jun 22 102 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller b) Standard mode `narrow window'. TDA955X/6X/8X PS/N1 series This mode is switched on when more than 15 succeeding vertical sync pulses are detected in the narrow window. When the circuit is in the standard mode and a vertical sync pulse is missing the retrace of the vertical ramp generator is started at the end of the window. Consequently, the disturbance of the picture is very small. The circuit will switch back to the search window when, for 6 successive vertical periods, no sync pulses are found within the window. c) Standard TV-norm (divider ratio 525 (60 Hz) or 625 (50 Hz). When the system is switched to the narrow window it is checked whether the incoming vertical sync pulses are in accordance with the TV-norm. When 15 standard TV-norm pulses are counted the divider system is switched to the standard divider ratio mode. In this mode the divider is always reset at the standard value even if the vertical sync pulse is missing. When 3 vertical sync pulses are missed the system switches back to the narrow window and when also in this window no sync pulses are found (condition 3 missing pulses) the system switches over to the search window. The vertical divider needs some waiting time during channel-switching of the tuner. When a fast reaction of the divider is required during channel-switching the system can be forced to the search window by means of the NCIN bit in subaddress 25H. When RGB signals are inserted the maximum vertical frequency is increased to 72 Hz. This has the consequence that the circuit can also be synchronised by signals with a higher vertical frequency like VGA. 49. Conditions: frequency is 50 Hz; normal mode; VS = 1F. 50. The output range percentages mentioned for E-W control parameters are based on the assumption that 400 A variation in E-W output current is equivalent to 20% variation in picture width. 51. The ICs have a zoom adjustment possibility for the horizontal and vertical deflection. For this reason an extra DAC has been added in the vertical amplitude control which controls the vertical scan amplitude between 0.75 and 1.38 of the nominal scan. At an amplitude of 1.06 of the nominal scan the output current is limited and the blanking of the RGB outputs is activated. This is illustrated in Fig. 43. When the vertical amplitude is compressed (zoom factor <1) it is still possible to display the black-current measuring lines in the vertical overscan. The feature is activated by means of the OSVE-bit in sub-address 26H. Because the vertical deflection output stage needs some time for the excursion from the top of the picture to the required position on the screen the vertical blanking is increased when the OSVE-bit is activated. The shape of the vertical deflection current for a zoom factor of 0.75 with OSVE activated is given in Fig. 44. The exact timing of the measuring pulses and vertical blanking for the various conditions is given in Fig. 46. a) The nominal scan height must be adjusted at a position of 19 HEX of the vertical `zoom' DAC. 52. At a chrominance input voltage of 660 mV (p-p) (colour bar with 75% saturation i.e. burst signal amplitude 300 mV (p-p)) the dynamic range of the ACC is +6 and -20 dB. 53. The ACL function can be activated by via the ACL bit in the subaddress 20H. The ACL circuit reduces the gain of the chroma amplifier for input signals with a chroma-to-burst ratio which exceeds a value of 3.0. 54. This parameter indicates the bandwidth of the complete chrominance circuit including the chrominance bandpass filter. The bandwidth of the low-pass filter of the demodulator is approximately 1 MHz. 55. The subcarrier output is combined with a 3-level switch output which can be used to switch external circuits like sound traps etc. This output is controlled by the CMB1 and CMB0 bits in control byte 22H. The subcarrier signal is available when CMB1/0 are set to 0/1. During the demodulation of SECAM signals the subcarrier signal is only available during the vertical retrace period. The frequency is 4.43 MHz in this condition. When CMB1/0 are set to 00 in versions for 90 picture tubes (no EW output) the output is high ohmic. 56. Because of the 2-point black current stabilization circuit both the black level and the amplitude of the RGB output signals depend on the drive characteristic of the picture tube. The system checks whether the returning measuring currents meet the requirement and adapts the output level and gain of the circuit when necessary. Therefore the typical value of the black level and amplitude at the output are just given as an indication for the design of the RGB output stage. 2000 Jun 22 103 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series The 2-point black level system adapts the drive voltage for each cathode in such a way that the 2 measuring currents have the right value. This has the consequence that a change in the gain of the output stage will be compensated by a gain change of the RGB control circuit. Because different picture tubes may require different drive voltage amplitudes the ratio between the output signal amplitude and the inserted measuring pulses can be adapted via the I2C-bus. This is indicated in the parameter `Adjustment range of the cathode drive level'. Because of the dependence of the output signal amplitude on the application the soft clipping limiting has been related to the input signal amplitude. 57. The alignment system for the Vg2 voltage of the picture tube can be activated by means of the AVG bit. In that condition a certain black level is inserted at the RGB outputs during a few lines. The value of this level can be adjusted by means of the brightness control DAC. An automatic adjustment of the Vg2 of the picture tube can be realised by using the WBC and HBC bits in output byte 01. For a black level feedback current between 12 and 20 A the WBC = 1, for a higher or lower current WBC = 0. Whether the current is too high or too low can be found from the HBC bit. The indication of these bits can be made visible on the screen via OSD so that this alignment procedure can also be used for service purposes. 58. When the reproduction of 4 : 3 pictures on a 16 : 9 picture tube is realised by means of a reduction of the horizontal scan amplitude the edges of the picture may slightly be disturbed. This effect can be prevented by adding an additional blanking to the RGB signals. The blanking pulse is derived form the horizontal oscillator and is directly related to the incoming video signal (independent of the flyback pulse). This blanking is activated with the HBL bit. The width of the blanking can be set by means of the bits WBF3-WBF0 (start of blanking) and WBR3-WBR0 (end of blanking) in subaddress 03H (see Fig.48). 59. Signal-to-noise ratio (S/N) is specified as peak-to-peak signal with respect to RMS noise (bandwidth 5 MHz). 60. This is a current input. The timing of the measuring pulses and the vertical blanking for the 50/60 Hz standard are given in Fig.46 The start-up procedure is as follows. When the TV receiver is switched-on the RGB outputs are blanked and the black-current loop will try to adjust the picture tube to the right bias levels. The RGB drive signals are switched-on as soon as the black current loop is stabilised. This results in the shortest switch-on time. When this switch-on system results in a visible disturbance of the picture it is possible to add a further switch-on delay via a software routine. In that case the RGB outputs must be blanked by means of the RBL bit. As soon as the black current loop is stabilised the BCF-bit is set to 0 (output byte 01). This information can then be used to switch-on the RGB outputs with some additional delay. 61. The vertical guard function has been combined with the black current measuring input. For a reliable operation of the protection system and to avoid that the black current stabilization system is disturbed the end of the protection pulse during normal operation should not overlap the measuring pulses (see also Fig.46). Therefore this pulse must end before line 14. 62. During switch-off the magnitude of the discharge current of the picture tube is controlled by the black current loop. Dependent on the setting of the OSO bit the vertical scan can be stopped in an overscan position during that time so that the discharge is not visible on the screen. The switch-off procedure is as follows: a) When the switch-off command is received the RGB outputs are blanked for a time of about 2 ms. b) If OSO = 1 the vertical scan is placed in an overscan position c) If OSO = 0 the vertical deflection will keep running during the switch-off time d) The soft-stop procedure is started with a reduction of the TON of the output stage from nominal to zero e) The fixed beam current is forced via the black current loop The soft-stop time has a value of 43 ms, the fixed beam current is flowing during a time of 38 ms. 2000 Jun 22 104 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 63. The control circuit contains a Peak White Limiting (PWL) circuit and a soft clipper. a) The detection level of the PWL is adjustable via the I2C-bus and has a control range between 0.55 and 0.85 VBL-WH (this amplitude is related to the CVBS/Y input signal (typical amplitude 1.0 VBL-WH) at maximum contrast setting). The high frequency components of the video signal are suppressed so that they do not activate the limiting action. The contrast reduction of the PWL is obtained by discharging the capacitor of the beam current limiting input. b) In addition to the PWL circuit the IC contains a soft clipper function which limits the high frequency signals when they exceed the peak white limiting level. The difference between the peak white limiting level and the soft clipping level is adjustable via the I2C-bus and can be varied between 0 and 10% in 3 steps (soft clipping level equal or higher than the PWL level). It is also possible to switch-off the soft clipping function. 64. The soft clipper gain reduction is measured by applying a sawtooth signal with rising slope and 0.7 VBL-WH at the CVBS input. To prevent the beam current limiter from operating a DC voltage of 3.5V must be applied to BCLIN pin. The contrast is set at the maximum value, the PWL (peak white limiting) level at the minimum value, and the soft clipping level is set at 0% above the PWL level (SOC10=00). The tangents of the sawtooth waveform at one of the RGB outputs is now determined at begin and end of the sawtooth. The soft clipper gain reduction is defined as the ratio of the slopes of the tangents for black and white, see Fig.47. Table 147 Some examples for the FM-PLL filter BL-3dB (kHz) 100 160 CS (nF) 4.7 4.7 CP (nF) 820 330 R (k) 2.7 3.9 0.5 0.5 Table 148 Output current of the phase detector in the various conditions I2C-BUS COMMANDS VID - - - - - - - - 0 - Note 1. Gating is active during vertical retrace, the width is 22 s. This gating prevents disturbance due to Macro Vision Anti Copy signals. 2. Gating is continuously active and is 5.7 s wide POC 0 0 0 0 0 0 0 - 0 1 FOA 0 0 0 0 0 1 1 1 - - FOB 0 0 0 1 1 0 0 1 - - IFI yes yes yes yes yes yes yes - no - IC CONDITIONS SL yes yes no yes no yes yes - - - NOISE no yes - - - no yes - - - SCAN 200 30 200 30 200 200 30 200 6 - -1 CURRENT/MODE V-RETR 300 30 300 30 300 300 30 300 6 - GATING yes (1) yes(2) no yes(2) no yes(2) yes(2) yes(1) no - MODE normal normal normal slow slow slow/fast slow/fast fast OSD off 2000 Jun 22 105 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series handbook, halfpage gm Co Ci XTALIN XTALI 276 100 k 1 f osc = ---------------------------------------C i x C tot 2 L i x --------------------C i + C tot XTALOUT XTALO Ca x Cb C tot = C p + ------------------Ca + Cb Li Cp Cx1 Ca Ci Ri crystal or ceramic resonator Cx2 Cb MGR447 Ca = Ci + Cx1 Cb = Co + Cx2 Fig.29 Simplified diagram crystal oscillator. 2000 Jun 22 106 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series % dB 0 80 -20 60 -40 40 -60 20 -80 0 0 -20 0 10 20 30 40 DAC (HEX) Overshoot in direction `black'. 10 20 30 40 DAC (HEX) Fig. 30 Volume control curve Fig. 31 Peaking control curve. MLA740 - 1 300 250 +50 (deg) +30 (%) % 225 250 200 175 150 200 +10 125 150 100 -10 100 75 50 25 -30 50 0 0 -50 0 10 20 30 40 DAC(HEX) 0 10 20 30 40 DAC (HEX) Fig.32 Hue control curve. Fig. 33 Saturation control curve. 2000 Jun 22 107 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series MLA741 - 1 100 (%) 90 80 70 60 50 40 30 MLA742 - 1 0.7 (V) 0.35 0 0.35 20 10 0.7 0 10 20 30 40 DAC (HEX) 0 0 10 20 30 40 DAC (HEX) Fig. 34 Contrast control curve. Fig. 35 Brightness control curve. MBC211 MBC212 100% 16 % 100% 92% 86% 72% 58% 44% 30% 30% 10 12 for negative modulation 100% = 10% rest carrier 22 26 32 36 40 44 48 52 56 60 64 s Fig. 36 Video output signal. Fig. 37 Test signal waveform. 2000 Jun 22 108 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 3.2 dB 10 dB 13.2 dB 30 dB 13.2 dB 30 dB SC CC BLUE PC SC CC YELLOW PC MBC213 PC SC ATTENUATOR TEST CIRCUIT SPECTRUM ANALYZER CC gain setting adjusted for blue MBC210 Input signal conditions: SC = sound carrier; CC = colour carrier; PC = picture carrier. All amplitudes with respect to top sync level. V O at 3.58 or 4.4 MHz Value at 0.92 or 1.1 MHz = 20 log ----------------------------------------------------------- + 3.6 dB V O at 0.92 or 1.1 MHz V O at 3.58 or 4.4 MHz Value at 2.66 or 3.3 MHz = 20 log ----------------------------------------------------------V O at 2.66 or 3.3 MHz Fig. 38 Test set-up intermodulation. 2000 Jun 22 109 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series CHARACTERISTIC POINTS AVL Deemphasis voltage FM swing 150 15 A 300 30 B 500 50 C 150 D 1500 UNIT mVRMS kHz 1.8 1.0 AVL is OFF AVL is ON 100.0m 10.0m 100.0m A B C 1.0 D 2.0 DEEMP Fig. 39 AVL characteristic 2000 Jun 22 110 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series OUTPUT (IRE) 100 80 60 40 20 B INPUT (IRE) 20 40 60 80 100 0 A B -20 A A-A: MAXIMUM BLACK LEVEL SHIFT B-B: LEVEL SHIFT AT 15% OF PEAK WHITE Fig. 40 I/O relation of the black level stretch circuit 2000 Jun 22 111 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series red V I-axis fully saturated colours yellow U Fig.41 Skin tone correction range for the correction angle of 123 deg. 2000 Jun 22 112 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series Output (%) 100 BLUE RED/GREEN (BLS=1) 95 90 85 80 85 90 95 100 Input (%) Fig.42 Blue stretch characteristic 2000 Jun 22 113 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series TOP % PICTURE 60 50 VERTICAL POSITION 138% 40 30 75% 20 10 0 -10 -20 -30 -40 -50 -60 BOTTOM PICTURE T/2 100% TIME T BLANKING FOR EXPANSION OF 138% Fig. 43 Vertical position and blanking pulse for 110 types 2000 Jun 22 114 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series V-DRIVE I-COIL Measuring lines Vertical blanking Fig.44 Measuring lines in vertical overscan for vertical compressed scan 2000 Jun 22 115 2000 Jun 22 116 Philips Semiconductors TV signal processor-Teletext decoder with embedded -Controller 100 Soft stop 75 Soft start TON (%) 50 TDA955X/6X/8X PS/N1 series 57 12 73 1045 43 Tentative Device Specification Time (ms) Discharge current picture tube 38 Fig. 45 Soft start and soft stop behaviour of horizontal output and timing picture tube discharge current RESET LINE COUNTER 23 625 50Hz 2000 Jun 22 1ST FIELD Video signal internal 2fH clock 14 lines Philips Semiconductors Reset Vert. Saw Vert. Blank L G B R 4.5 lines (OSVE = 0) 14.5 lines (OSVE = 1) Black current pulses end line 23 (OSVE = 0) end line 33 (OSVE = 1) 17 18 19 20 312 336 Video signal 2ND FIELD Vert. Blank L G B R 4.5 lines (OSVE = 0) 14.5 lines (OSVE = 1) 329 330 331 332 line 335.5 (OSVE = 0) line 345.5 (OSVE = 1) Black current pulses TV signal processor-Teletext decoder with embedded -Controller 117 60Hz internal 2fH clock 9.5 lines end line 20(OSVE = 0) end line 32 (OSVE = 1) 1ST FIELD Reset Vert. Saw Vert. Blank L R G B 4 lines (OSVE = 0) 16 lines (OSVE = 1) Black current pulses 17 18 19 20 line 282.5 (OSVE = 0) line 294.5 (OSVE = 1) 2ND FIELD L R G B 4 lines (OSVE = 0) 16 lines (OSVE = 1) Black current pulses Vert. Blank 279 280 281 282 TDA955X/6X/8X PS/N1 series Tentative Device Specification Fig.46 Timing of vertical blanking and black current measuring pulses Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller 4.0 TDA955X/6X/8X PS/N1 series clipper off Soft clipping range (Defined by SOC1/SOC0 bits) 3.0 RGBout (Vb-w) 2.0 clipper on 1.0 20 40 00H 60 08H PWL setting 80 0FH 100 YIN (IRE) 120 130 Fig.47 Peak White Limiting / Soft clipper characteristic. VIDEO REF -1 BURST KEY 15 steps of 0.16 s 3.5 s 5.9 s 7.8 s BLANKING 10.2 s 15 steps of 0.16 s Fig.48 Timing of horizontal wide blanking 2000 Jun 22 118 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TEST AND APPLICATION INFORMATION East-West output stage In order to obtain correct tracking of the vertical and horizontal EHT-correction, the EW output stage should be dimensioned as illustrated in Fig.49. Resistor REW determines the gain of the EW output stage. Resistor Rc determines the reference current for both the vertical sawtooth generator and the geometry processor. The preferred value of Rc is 39 k which results in a reference current of 100 A (Vref = 3.9 V). TDA955X/6X/8X PS/N1 series The value of REW must be: V scan R EW = R c x ---------------------18 x V ref Example: With Vref = 3.9 V; Rc = 39 k and Vscan = 120 V then REW = 68 k. handbook, full pagewidth VDD HORIZONTAL DEFLECTION STAGE R ew V scan TDA 935X TDA8366 UOC series 21 15 43 EWD EW output stage DIODE MODULATOR V EW 28 50 20 Rc 39 k (2%) I ref V ref 27 49 21 C saw 100 nF (5%) MLA744 - 1 Fig. 49 East-West output stage. 2000 Jun 22 119 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series 700 IVERT 500 (A) 300 100 -100 -300 -500 -700 0 T/2 TIME T VA = 0, 1FH and 3FH; VSH = 1FH; SC = 0EH. VS = 0, 1FH and 3FH; VA = 1FH; VSH = 1FH; SC = 0EH. Fig. 50 Control range of vertical amplitude. Fig. 51 Control range of vertical slope. IVERT (A) 600 400 200 0 -200 -400 -600 -1.0 -500.0m -750.0m -250.0m 0.0 500.0m 250.0m 1.0 750.0m 0 T/2 TIME T VSH = 0, 1FH and 3FH; VA = 1FH; SC = 0EH. SC = 0, 0EH and 3FH; VA = 1FH; VSH = 1FH. Fig. 52 Control range of vertical shift. Fig. 53 Control range of S-correction. 2000 Jun 22 120 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller TDA955X/6X/8X PS/N1 series IEW (A) 1200 1000 800 IEW (A) 500 400 300 600 200 400 200 0 0.0 100 0 0 400.0m 200.0m T/2 600.0m TIME 800.0m T 1.0 0.0 0 400.0m 200.0m T/2 600.0m TIME 800.0m T 1.0 PW = 0, 1FH and 3FH; EW = 3FH; TC = 1FH; CP = 11H. EW = 0, 1FH and 3FH; PW = 3FH; TC = 1FH; CP = 11H. Fig. 54 Control range of EW width. Fig. 55 Control range of EW parabola/width ratio. IEW (A) 600 500 400 300 200 IEW (A) 650 600 550 500 450 100 400 0 0.0 0 400.0m 200.0m T/2 600.0m TIME 800.0m T 1.0 350 0.0 0 400.0m 200.0m T/2 600.0m TIME800.0m T 1.0 CP = 0, 11H and 3FH; EW = 3FH; PW = 3FH; TC = 1FH. TC = 0, 1FH and 3FH; EW = 1FH; PW = 1FH; CP = 11H. Fig. 56 Control range of EW corner/parabola ratio. Fig. 57 Control range of EW trapezium correction. 2000 Jun 22 121 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller Adjustment of geometry control parameters The deflection processor offers 5 control parameters for picture alignment, viz: * S-correction * vertical amplitude * vertical slope * vertical shift * horizontal shift. The 110 types offer in addition: * EW width * EW parabola width * EW upper/lower corner parabola * EW trapezium correction. * Vertical zoom * Horizontal parallelogram and bow correction for some versions in the range It is important to notice that the ICs are designed for use with a DC-coupled vertical deflection stage. This is the reason why a vertical linearity alignment is not necessary (and therefore not available). For a particular combination of picture tube type, vertical output stage and EW output stage it is determined which are the required values for the settings of S-correction, EW parabola/width ratio and EW corner/parabola ratio. These parameters can be preset via the I2C-bus, and do not need any additional adjustment. The rest of the parameters are preset with the mid-value of their control range (i.e. 1FH), or with the values obtained by previous TV-set adjustments. The vertical shift control is meant for compensation of off-sets in the external vertical output stage or in the picture tube. It can be shown that without compensation these off-sets will result in a certain linearity error, especially with picture tubes that need large S-correction. The total linearity error is in first order approximation proportional to the value of the off-set, and to the square of the S-correction needed. The necessity to use the vertical shift alignment depends on the expected off-sets in vertical output stage and picture tube, on the required value of the S-correction, and on the demands upon vertical linearity. TDA955X/6X/8X PS/N1 series For adjustment of the vertical shift and vertical slope independent of each other, a special service blanking mode can be entered by setting the SBL bit HIGH. In this mode the RGB-outputs are blanked during the second half of the picture. There are 2 different methods for alignment of the picture in vertical direction. Both methods make use of the service blanking mode. The first method is recommended for picture tubes that have a marking for the middle of the screen. With the vertical shift control the last line of the visible picture is positioned exactly in the middle of the screen. After this adjustment the vertical shift should not be changed. The top of the picture is placed by adjustment of the vertical amplitude, and the bottom by adjustment of the vertical slope. The second method is recommended for picture tubes that have no marking for the middle of the screen. For this method a video signal is required in which the middle of the picture is indicated (e.g. the white line in the circle test pattern). With the vertical slope control the beginning of the blanking is positioned exactly on the middle of the picture. Then the top and bottom of the picture are placed symmetrical with respect to the middle of the screen by adjustment of the vertical amplitude and vertical shift. After this adjustment the vertical shift has the right setting and should not be changed. If the vertical shift alignment is not required VSH should be set to its mid-value (i.e. VSH = 1F). Then the top of the picture is placed by adjustment of the vertical amplitude and the bottom by adjustment of the vertical slope. After the vertical picture alignment the picture is positioned in the horizontal direction by adjustment of the EW width and the horizontal shift. Finally (if necessary) the left- and right-hand sides of the picture are aligned in parallel by adjusting the EW trapezium control. To obtain the full range of the vertical zoom function the adjustment of the vertical geometry should be carried out at a nominal setting of the zoom DAC at position 19 HEX. 2000 Jun 22 122 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller PACKAGE OUTLINE SDIP64: plastic shrink dual in-line package; 64 leads (750 mil) TDA955X/6X/8X PS/N1 series SOT274-1 seating plane D ME E A2 A 2 L A1 1 c Z e b1 1 b 64 33 wM M (e 1) 1 MH H pin 1 index E 1 32 0 5 scale 10 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 5.84 A1 1 min. 0.51 A2 2 max. 4.57 b 1.3 0.8 b1 1 0.53 0.40 c 0.32 0.23 (1) D (1) (1) E (1) e 1.778 e1 1 19.05 L 3.2 2.8 ME E 19.61 19.05 MH H 20.96 19.71 w 0.18 (1) Z (1) max. 58.67 57.70 17.2 16.9 1.73 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT274-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 92-10-13 95-02-04 2000 Jun 22 123 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC package Databook" (order code 9398 652 90011). SDIP SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. REPAIRING SOLDERED JOINTS Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. QFP REFLOW SOLDERING Reflow soldering techniques are suitable for all QFP packages. The choice of heating method may be influenced by larger plastic QFP packages (44 leads, or more). If infrared or vapour phase heating is used and the large packages are not absolutely dry (less than 0.1% moisture content by weight), vaporization of the small amount of moisture in them can cause cracking of the plastic body. For details, refer to the Drypack information in our "Quality Reference Handbook" (order code 9397 750 00192). TDA955X/6X/8X PS/N1 series Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 50 and 300 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250 C. WAVE SOLDERING Wave soldering is not recommended for QFP packages. This is because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices. If wave soldering cannot be avoided, for QFP packages with a pitch (e) larger than 0.5 mm, the following conditions must be observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The footprint must be at an angle of 45 to the board direction and must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. REPAIRING SOLDERED JOINTS Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. 2000 Jun 22 124 Philips Semiconductors Tentative Device Specification TV signal processor-Teletext decoder with embedded -Controller DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values TDA955X/6X/8X PS/N1 series This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. PURCHASE OF PHILIPS I2C COMPONENTS Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. 2000 Jun 22 125 |
Price & Availability of TDA958X
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |